manualshive.com logo in svg

Meritor MM-0861, Maintenance Manual

Share
Download
Meritor MM-0861 Maintenance Manual Download Page 96

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 94

Printed in USA

10     Troubleshooting

PTO Does Not Engage/Disengage Diagnostics

Check air connection to 

PTO shift port.

Return the vehicle 
to service.

Check indicator light,
and engagement and
disengagement sensors
for correct operation.

Check the available air pressure.
 The transfer case requires at
least 60 psi (4.14 bar) at all 

times to operate correctly.

Yes

Yes

Yes

Yes

Yes

No

No

No

No

Replace faulty indicator 
light or sensor, then try
to shift PTO.

Correct system air pressure.
Refer to the vehicle
manufacturer’s instructions.

Check the piston cylinder on the
PTO. Clean the air supply system. 
Refer to vehicle manufacturer’s 
instructions. Check that the PTO
engages correctly.

Return the vehicle to service.

Check the PTO for leaks. 

Reassemble and install the PTO on the
transfer case. Road test the vehicle to
confirm the problem is corrected.

No

Remove the PTO from the transfer case.
Disassemble the PTO and inspect the
bearings, shift collar, shift fork declutch
bore and return spring for damage.
Repair all damaged components.

Verify the PTO engages and

disengages correctly.

Light or 

sensor 
faulty?

Air 

pressure 65 psi

(4.48 bar) or

more?

Air 

system

contaminated?

4001528d

PTO

shifts

correctly? 

PTO

shifts

correctly? 

Return the vehicle 
to service.

Return the vehicle 
to service.

Return the vehicle 
to service.

Figure 10.4 

Summary of Contents for MM-0861























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands