manualshive.com logo in svg

Meritor MM-0861, Maintenance Manual

Share
Download
Meritor MM-0861 Maintenance Manual Download Page 49

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 47

Printed in USA

5     Disassembly

4000202b

Figure 5.13 

2.  Remove the yoke nut, washer, and yoke. Use a yoke puller to 

remove the yoke.

3.  Remove the PTO indicator switch from the shift plate, if 

equipped.

4.  Remove the cage mounting capscrews and washers from the 

PTO. Lift the PTO assembly off the transfer case.

Remove the Front Input Shaft, Input Bearing Cage, and 
Internal Pump Assembly (If Equipped)

1.  On transfer cases with an internal oil pump, remove the inlet 

oil tube from the transfer case by loosening the fittings at the 
lower front case and input-bearing cage. Figure 5.14.

MTC-4208X/XP, MTC-4210X/XP, AND MTC-4213X

4006988a

WITH INTERNAL OIL PUMP

INLET

TUBE

FITTINGS

DRAIN

PLUG

FILL

PLUG

FRONT VIEW

Figure 5.14 

2.  On transfer case models MTC-4208X/XP and MTC-4210X/

XP, remove the PTO cover or PTO, whichever applies. Use a 3” 
socket to remove the large retaining nut and washer from the 
rear half of the input shaft. Use a yoke tool on the input shaft 
yoke to prevent the shaft from rotating while removing the 
retaining nut. 

 
If the input shaft retaining nut cannot be removed, it will not 
be possible to remove the front input shaft before opening the 
housing. Skip this procedure. 

 

NOTE: 

The MTC-4213X has a split shaft design. It is only 

necessary to remove the front half of the input shaft during 
disassembly. The rear half of the input shaft is pressed into 
the rear case half and cannot be removed until after the 
transfer case halves are separated.

3.  On transfer case models MTC-4208XL/XLEV/XLEC and 

MTC-4210XL/XLEV/XLEC, use a 3” socket to remove the large 
retaining nut and washer from the rear half of the input shaft. 
Use a yoke tool on the input shaft yoke to prevent the shaft 
from rotating when removing the retaining nut.  

 
If the input shaft retaining nut cannot be removed, it will not 
be possible to remove the front input shaft before opening the 
housing. Skip this procedure.

4.  Remove the capscrews securing the input bearing cage and 

internal pump assembly, if equipped. 
 

Summary of Contents for MM-0861























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands