manualshive.com logo in svg

Meritor MM-0861, Maintenance Manual

Share
Download
Meritor MM-0861 Maintenance Manual Download Page 66

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 64

Printed in USA

7     Assembly

8.  Place the oil pump, if equipped, and input bearing cage 

assembly over the input shaft. The drive teeth on the inner 
pump rotor must engage the teeth on the input shaft. NEVER 
use force to engage the splines. If a sealing ring is broken, 
remove and replace the pump.

9.  Place the assembly into a holding fixture (refer to "Holding 

Fixture (905473-140)" on page 108) and install the yoke 
assembly.

10.  Install the washer and yoke nut. Tighten the yoke nut to 700-

900 lb-ft (949-1220 Nm).

Assemble the Upper Rear Output Shaft 
(MTC-4213X Only)

1.  Place the shaft into a holding fixture with the larger end facing 

UP.

2.  Align the internal splines of the high range helical gear with 

the shaft splines and install the gear onto the shaft. Ensure 
the clutch collar gears are facing UP. Figure 7.12.

4007168a

CLUTCH

COLLAR

SPLINES

REAR

OUTPUT

SHAFT

HELICAL

GEAR

Figure 7.12 

3.  Turn the shaft assembly over and secure it in a holding fixture.

4.  Use a press and sleeve to press the bearing DOWNWARD 

onto the output shaft until it bottoms out against the helical 
gear. Refer to "Bearing Cone Driver (905473-82)" on page 
111. Use a 0.002” shim or feeler gauge to verify the bearing 
is fully seated against the gear. Figure 7.13.

SLEEVE,

TOOL

905473-82

4007167a

HELICAL

GEAR

BEARING

PRESS

Figure 7.13 

Gear and Shaft Installation into the 
Transfer Case Halves

Before installing the gear shafts, refer to "End Play Check and 
Adjustment" on page 67 for the correct shim pack starting 
thickness.

1.  Lubricate all bearing cups and cones, gears, and shaft 

assemblies before installation into the case. Use SAE Grade 
full-synthetic 40W or 50W oil, Meritor specification O-81.

2.  Use a mallet or press and sleeve to install the bearing cups 

into the bore until correctly seated. Refer to "Tools" on page 
108 to identify the correct sleeve for the model being 
serviced. Refer to "End Play Check and Adjustment" on page 
67 for initial shim stack up requirements. Figure 7.14.

NOTE: The sleeve tool number will vary by model

4007156a

PRESS

SLEEVE,

TOOL

905473-92

BEARING

CUP

Figure 7.14 

3.  With the inside of the front case facing UPWARD, install the 

single idler shaft (MTC-4213X only), or rear output shaft 
(MTC-4208X/XP/XL/XLEV/XLEC and MTC-4210X/XP/XL/XLEV/
XLEC), and double-gear idler shaft assemblies (all models). 
Figure 7.15.

4000203a

Figure 7.15 

4.  Position the clutch collar onto the shift fork. Position the shift 

fork and clutch collar onto the front output shaft clutch hub.

Summary of Contents for MM-0861























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands