manualshive.com logo in svg

Meritor MM-0861, Maintenance Manual

Share
Download
Meritor MM-0861 Maintenance Manual Download Page 83

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 81

Printed in USA

8     Power Takeoff (PTO)

Remove the Transfer Case Rear Access 
Cover

1.  Park the vehicle on a level surface. Block the wheels to 

prevent the vehicle from moving.

2.  Remove the air from the vehicle’s system.

3.  Place a suitable container under the transfer case to catch the  

hydraulic fluid when removing the rear access cover.

4.  Remove the mounting bolts and washers securing the rear- 

mounted pump housing. Figure 8.2. 
 

NOTE:

 It is necessary to replace the rear-mounted pump with  

the internal pump in order to install the PTO. Refer to 
Technical Bulletin TP-0708 - Removing the External Oil Pump 
and Installing the Internal Oil Pump for the correct kit and 
instructions.

5.  Clean the PTO mounting surface to remove all sealant.

Summary of Contents for MM-0861























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands