MerCruiser 6.2 MPI User Manual Download Page 77 | Manualshive

Page: 77 / 110

background image

Section 5 - Maintenance

90-864197072 NOVEMBER 2007

Page 69

NOTICE

Flushing the engine when it is not operating will result in water collecting in the exhaust

system, damaging the engine. Do not supply flush water for more than 15 seconds without

the engine operating.

3. Completely open the water source to provide maximum water supply.
4. Place the remote control in the neutral idle speed position.
5. Immediately start the engine.

NOTICE

Operating the engine out of the water at high speeds creates suction, which can collapse

the water supply hose and overheat the engine. Do not operate the engine above 1400

RPM out of the water and without sufficient cooling water supply.

6. Depress the throttle only button and slowly advance the throttle until the engine reaches

1300 RPM (± 100 RPM).

7. Observe the water temperature gauge to ensure that the engine is operating in the

normal range.

8. Operate the engine with the transmission in neutral for a minimum of 10 minutes.
9.

For power packages operated in salty, brackish, mineral‑laden or polluted water:

Continue to operate the engine until the discharge water is clear.

10. Slowly return the throttle to idle speed position.

NOTICE

Flushing the engine when it is not operating will result in water collecting in the exhaust

system, damaging the engine. Do not supply flush water for more than 15 seconds without

the engine operating.

11. Stop the engine.
12. Immediately shut off the supply water and remove the flushing attachment.
13. Install the water inlet hose to the seawater inlet of the seawater pump or V‑Drive water

inlet.

14. Tighten hose clamp securely.
15. Attach to the next engine, if equipped, and repeat procedure.

The Boat In the Water

IMPORTANT: Flushing the power package is most effective when performed with the boat

out of the water.
IMPORTANT: Flushing is needed If the engine package has been operated in salty,

brackish, mineral‑laden or polluted water. For best results flushing is recommended after

each outing and before cold weather and extended storage.

NOTICE

Disconnecting the seawater inlet hose will cause water to enter the bilge resulting in

engine damage. Close the seacock before disconnecting the seawater inlet hose. Plug

the seawater inlet hose immediately after disconnecting it.

1.

Models with Walter V-Drive Transmissions:

a.

Close the seacock, if equipped, and then disconnect the seawater inlet hose from

the transmission seawater inlet fitting.

«
...
75
76
77
78
79
...
»

Summary of Contents for 6.2 MPI















































































































Reviews:

No comments

Related manuals for 6.2 MPI

Brand: BAFANG Pages: 12

Vickers M2-200 Series

Brand: Eaton Pages: 13

Vanguard 290000

Brand: Briggs & Stratton Pages: 68

Brand: TAARKS Pages: 7

Brand: Eurotronic Pages: 4

MICROPUMP EagleDrive MS

Brand: Idex Pages: 23

Brand: Man Pages: 132

Brand: Key Automation Pages: 44

Brand: STG-BEIKIRCH Pages: 9

Brand: DJ ENGINE Pages: 9

Brand: Jabiru Pages: 56

Brand: GSK Pages: 24

Brand: DLE Pages: 4

Brand: Pratt & Whitney Pages: 576

Brand: Honda Pages: 16

Brand: Honda Pages: 16

Brand: panthera Pages: 12

Brand: M.T.H. Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands