MerCruiser 6.2 MPI User Manual Download Page 45

Page: 45 / 110

Section 3 - On The Water

90-864197072 NOVEMBER 2007

Page 37

1. Refer to

Remote Controls

section for remote control features.

2. Move the control lever to the idle/neutral position.
3. Depress the throttle only button, and move the control lever to the idle/forward or idle/

reverse position. The DTS control system will sound two beeps on the audio warning

horn to indicate throttle only mode is active. On console mount remote controls, the

neutral light will begin to blink.

4. Advancing the control lever beyond the idle/forward or idle/reverse position will cause

engine speed to increase.

IMPORTANT: Moving the control lever back to the idle/neutral position will deactivate the

throttle only mode and allow the engine to shift into gear.
5. Throttle only mode is deactivated by moving the control lever to the idle/neutral position.

Moving the control lever from the idle/neutral position to the idle/forward or idle/reverse

position without pressing the throttle only button will shift the unit into the chosen gear.

Freezing Temperature Operation

IMPORTANT: If the boat is operated during periods of freezing temperature, precautions

must be taken to prevent freeze damage to the power package. Damage caused by

freezing is not covered by Mercury MerCruiser Limited Warranty.

Drain Plug and Bilge Pump

The engine compartment in your boat is a natural place for water to collect. For this reason,

boats are normally equipped with a drain plug and/or a bilge pump. It is very important to

check these items on a regular basis to ensure that the water level does not come into

contact with your power package. Components on your engine will be damaged if

submerged. Damage caused by submersion is not covered by the Mercury MerCruiser

Limited Warranty.

Protecting People in the Water

While You Are Cruising

It is very difficult for a person in the water to take quick action to avoid a boat heading in

their direction, even at slow speeds.

21604

Always slow down and exercise extreme caution any time you are boating in an area where

there might be people in the water.
Whenever a boat is moving (even coasting) and the gear shift is in neutral, there is sufficient

force by the water on the propeller to cause the propeller to rotate. This neutral propeller

rotation can cause serious injury.

While Boat Is Stationary

WARNING

A spinning propeller, a moving boat, or any solid device attached to the boat can cause

serious injury or death to swimmers. Stop the engine immediately whenever anyone in

the water is near your boat.

Summary of Contents for 6.2 MPI















































































































Search results

Summary of Contents for 6.2 MPI

Reviews:

Related manuals for 6.2 MPI

Brands by name

Popular brands

MerCruiser 6.2 MPI, User Manual

Search results

Summary of Contents for 6.2 MPI

Reviews:

Related manuals for 6.2 MPI

Brands by name

Popular brands