MerCruiser 350 MAG MPI User Manual Download Page 69

Page: 69 / 150

Section 4 - Specifications

90-864195070 JUNE 2007

Page 61

5.0 MPI, 350 MAG MPI, MX 6.2 MPI

(includes Horizon) Models

Capacity

Fluid Type

Engine oil (with filter)

4.25 liters (4.5 U.S. qt.) Mercury/Quicksilver Synthetic Blend

MerCruiser Engine Oil 25W‑40

Seawater cooling system (winterization

use only)

20 liters (21 U.S. qt.)

Propylene Glycol and Purified Water

Closed cooling system

19 liters (20 U.S. qt.)

Mercury Extended Life Coolant/

Antifreeze or Extended Life Ethylene

Glycol 5/100 Coolant/Antifreeze mixed

50/50 with Purified Water

Alpha Sterndrive

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Alpha One

1892 ml (64 oz.)

High Performance Gear Lubricant

Bravo Sterndrives

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Bravo One

2736 ml (92‑1/2 oz.)

High Performance Gear Lubricant

Bravo Two

3209 ml (108‑1/2 oz.)

Bravo Three

2972 ml (100‑1/2 oz.)

Power‑Assisted Steering and Power Trim Fluids

APPROVED POWER-ASSISTED STEERING FLUIDS

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

Dexron III Automatic Transmission Fluid

Obtain Locally

APPROVED POWER TRIM FLUIDS

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

SAE Engine Oil 10W 30

Obtain locally

SAE Engine Oil 10W 40

Summary of Contents for 350 MAG MPI























































































































































Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands

MerCruiser 350 MAG MPI, User Manual

Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands