MerCruiser 350 MAG MPI User Manual Download Page 68

Page: 68 / 150

Section 4 - Specifications

Page 60

90-864195070 JUNE 2007

Models

4.3 MPI

5.0 MPI

350 MAG MPI

Horizon

MX 6.2 MPI

Horizon

Horsepower

220

260

300

320

Kilowatts

164

194

224

238

Number of cylinders

Displacement

4.3 L (262 cid)

5.0 L (305 cid)

5.7 L (350 cid)

6.2 L (377 cid)

Bore and Stroke

101.6 × 88.39 mm

(4.012 × 3.48 in.)

94.89 × 88.39 mm

(3.735 × 3.48 in.)

101.6 × 88.39 mm

(4.00 × 3.48 in.)

101.6 × 95.25 mm

(4.00 × 3.75 in.)

Compression ratio

9.2:1

9.4:1

9.0:1

Idle RPM in neutral

600

Specified WOT RPM range

4400‑4800

4600‑5000

4800‑5200

Minimum oil pressure @ idle

41 kPa (6 psi)

Thermostat (seawater cooled

models)

71° C (160° F)

Thermostat (closed cooled

models)

77° C (170° F)

Timing @ idle

Not Adjustable

Firing order

1‑6‑5‑4‑3‑2

1‑8‑4‑3‑6‑5‑7‑2

Electrical system

12‑Volt Negative (‑) Ground

Alternator rating

65 amp

Recommended battery rating

(Non‑DTS models) (minimum)

750 CCA, 950 MCA, or 180 Ah

Recommended battery rating

(DTS models) (minimum)

800 CCA, 1000 MCA, or 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Fluid Specifications (MPI)

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Engine

IMPORTANT: It may be necessary to adjust oil levels depending on installation angle and

cooling systems (heat exchanger and fluid lines).
Always use the dipstick to determine the exact quantity of oil or fluid required.

4.3L MPI Models

Capacity

Fluid Type

Engine oil (with filter)

3.8 liters (4 U.S. qt.) Mercury/Quicksilver Synthetic Blend

MerCruiser Engine Oil 25W‑40

Seawater cooling system (winterization use

only)

20 liters (21 U.S. qt.) Propylene Glycol and Purified Water

Closed cooling system

19 liters (20 U.S. qt.)

Mercury Extended Life Coolant/

Antifreeze or Extended Life Ethylene

Glycol 5/100 Coolant/Antifreeze mixed

50/50 with Purified Water

Summary of Contents for 350 MAG MPI























































































































































Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands

MerCruiser 350 MAG MPI, User Manual

Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands