MerCruiser 350 MAG MPI User Manual Download Page 143

Page: 143 / 150

Section 7 - Troubleshooting

90-864195070 JUNE 2007

Page 135

Possible Cause

Remedy

EFI system fault.

Have EFI System checked by an authorized Mercury

MerCruiser dealer.

Engine Runs Rough, Misses And/Or Backfires

Possible Cause

Remedy

Clogged fuel filter.

Replace filter.

Stale or contaminated fuel.

If contaminated, drain tank. Fill with fresh fuel.

Kinked or clogged fuel line or fuel tank vent line. Replace kinked lines or blow out lines with compressed air

to remove obstruction.

Flame Arrestor dirty.

Clean Flame Arrestor.

Faulty ignition system component.

Service ignition system.

Idle speed too low.

Have EFI system checked by an authorized Mercury

MerCruiser dealer.

EFI System fault.

Have EFI System checked by an authorized Mercury

MerCruiser dealer.

Poor Performance

Possible Cause

Remedy

Throttle not fully open.

Inspect the throttle cable and linkages for proper operation.

Damaged or improper propeller.

Replace the propeller.

Excessive bilge water.

Drain and check for cause of entry.

Boat overloaded or load improperly distributed. Reduce load or redistribute load more evenly.
Flame arrestor dirty.

Clean the flame arrestor.

Boat bottom fouled or damaged.

Clean or repair as necessary.

Ignition problem.

See

Engine Runs Rough, Misses or Backfires

Engine overheating.

See

Excessive Engine Temperature

EFI System fault

Have EFI System checked by an authorized Mercury

MerCruiser dealer.

Excessive Engine Temperature

Possible Cause

Remedy

Water inlet or seacock closed.

Open.

Drive belt loose or in poor condition.

Replace or adjust belt.

Seawater pickups or sea strainer obstructed.

Remove obstruction.

Faulty thermostat.

Replace.

Coolant level (if equipped) low in closed cooling

section.

Check for cause of low coolant level and repair. Fill

system with proper coolant solution.

Heat Exchanger or Fluid Cooler plugged with foreign

material

Clean Heat Exchanger, Engine Oil Cooler, and

Transmission Oil Cooler (if equipped).

Loss of pressure in closed cooling section.

Check for leaks. Clean, inspect and test pressure cap.

Faulty seawater pickup pump.

Repair.

Seawater discharge restricted or plugged.

Clean exhaust elbows.

Summary of Contents for 350 MAG MPI























































































































































Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands

MerCruiser 350 MAG MPI, User Manual

Search results

Summary of Contents for 350 MAG MPI

Reviews:

Related manuals for 350 MAG MPI

Brands by name

Popular brands