background image

P 10

17

Please retain product label and instructions for future reference

             

Step 14

Parts needed - No. 17 QTY 66 

Place the first floor board (No. 17)

inside the building flush to the log

board on one side. Continue adding

the floor boards (

internally

) making

sure to interlock each individual

board.

*Do 

NOT

 secure the boards until

the last board has been measured

and cut.

Following the same method outlined

previously, measure the gap between

the bottom of the tongue (on the last 

board placed) and the log board.

Using a straight edge mark out the 

measurement onto the last floor

board (No. 17) and cut along the 

length removing the excess.

**Please note:

 Mark the final board

2mm under the measurement; This

will allow the timber to expand and

contract correctly.

Once all the floor boards are in 

position secure each board into

position using 8x40mm screws.

***Please Note: 

Ensure to screw 

through each of the floor boards 

into the floor bearers.

528x40mm Screws 

40mm 

screw

Pre drill 

hole

*

Cut to fit

Roof

Closure Trim

Internal

25

Step 15

Parts needed - No. 25 QTY 9 

   

 

Inside the building place the closure 

trim (No. 25) against the boarding and 

align with the roof as shown in the 

illustration. 

Once in position fix each trim 

into place by pre drilling a pilot hole 

and using 6x30mm screws per trim, 

equally spacing them along the face of 

the board.

54x30mm Screws

Pre drill 

hole

30mm 

screw

*

trim to fit

*Measure and cut the

closure trims to

fit the internal space.

25

25

Step 16

Parts needed - No. 25 QTY 9 

Once the floor has been laid arrange the

closure trim (No. 25) around the outside edge 

of floor (internally), measure and cut down 

accordingly to best match the internal

space.

Secure each trim section into place

using 6x30mm spaced equally along the

board as shown in the illustration.

*Do NOT fix the closure trim to the floor

boards.

54x30mm Screws

 

30mm 

screw

Pre drill 

hole

*

Cut to fit

Summary of Contents for 0644LOG186-V4














Reviews: