MEN Mikro Elektronik BL50S User Manual Download Page 70

Page: 70 / 73

Maintenance

MEN Mikro Elektronik GmbH

20BL50S00 E2 – 2014-12-10

Maintenance

6.1

Cleaning the System

The system should be cleaned once a year. Clean the bottom and top plate, remove
dirt and dust from air ventilation holes. Light dirt can be removed with a dry cloth.
Persistent dirt should only be removed with a mild detergent and a soft cloth.

Take care that no liquid gets inside the system.

6.2

Fuse Protection

• Current rating: 8A

• Voltage rating: 350 VDC

• Type: Slow-blow

• Size: 5 x 20

• MEN part number: 5475-0026

Figure 19.

Position of the fuse in the interior of the BL50S (highlighted in red)

The DC/DC converter inside the Power Supply Unit is protected by a
fuse.

This fuse is not intended to be exchanged by the customer.

Your warranty for the Power Supply Unit will cease if you
exchange the fuse on your own.

Please send your unit to MEN for

repair if a fuse blows.

Summary of Contents for BL50S










































































Search results

Summary of Contents for BL50S

Reviews:

Related manuals for BL50S

Brands by name

Popular brands

MEN Mikro Elektronik BL50S, User Manual

Search results

Summary of Contents for BL50S

Reviews:

Related manuals for BL50S

Brands by name

Popular brands