background image

1-833-454-0864

7

LP CYLINDER FILLING

SAFETY HOSE AND REGULATOR

• 

Use only licensed and experienced dealers.

• 

Ensure that the dealer checks and tests the tank for leaks after filling. 

• 

LP dealer must purge new cylinder before filling.

• 

Dealer should NEVER fill LP cylinder more than 80% of LP cylinder volume. Volume of propane in cylinder will 

vary by temperature.

• 

Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.

• 

To remove gas from LP cylinder, contact an LP dealer or call a local fire department  

for assistance.

Your griddle is designed to operate on LP gas at a pressure of 2.74Kpa (11” 

water column). A regulator preset to this pressure is supplied with your Griddle.

SAFETY FEATURES

 of QCC-1 Quick Closing Coupling.

All models are designed to be used with an LP gas cylinder equipped with the 

new QCC-1 Quick Closing Coupling system. 

The QCC-1 System Incorporates 

SAFETY FEATURES

 required by the 

Canadian Standards Steering Committee.

1.  Gas will not flow until a positive connection has been made.
2. 

A thermal element will shut off the flow of gas between 240 degrees F and 

300 degrees F. This may result in a melted regulator hose. 

3.  When activated, a Flow Limiting Device will limit the flow of gas to 10 cubic feet per hour.
 

Connecting Regulator to the LP Cylinder

1.  Turn all control knobs to the “

OFF

” position.

2.  Turn LP cylinder “

OFF

” by turning hand-wheel clockwise to a full stop.

3.  Remove the protective cap from LP cylinder valve. Always use cap and strap 

supplied with valve.

4. 

Hold regulator and insert nipple into LP cylinder valve. Hand tighten the 

coupling nut. Hold the regulator in a straight line with LP cylinder valve so as 

not to cross-thread the connection.

5. 

Turn the coupling nut clockwise and tighten to a full stop. The regulator will 

seal on the back-check feature in the LP cylinder valve, resulting in some 

resistance.

     WARNING 

 

        If the above instructions are not completely adhered to, it could cause a fire/explosion, resulting in death or      

        serious Injury, or property damage.

     CAUTION 

     

A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LP gas dealer for      

        assistance.

Nipple has to be centered

 

into the LP cylinder valve.

Regulator

Heat sensitive hand wheel

Nipple with flow limiting device

Hold coupling nut 

and regulator as 

shown for proper 

connection to 

LP cylinder valve.

Shut off valve

Check 

valve

Summary of Contents for 980305015









































Reviews: