manualshive.com logo in svg

Megger Baker DX Series, Quick Reference Manual, Page: 23 / 28

Share
Download
Megger Baker DX Series Quick Reference Manual Download Page 23

Figure 25. Surge test results screen.

Basic Testing Procedures

Baker DX Series Static Motor Analyzer

www.megger.com

18

Figure 24. Ramp rate and waveform zoom popup menu.

6.  Use the 

Fast/Slow Ramp

 Rate icons to control the rate of voltage change while turning the 

Voltage Output Control

 knob clockwise to raise the voltage to the desired test level. Release 

the knob when the test voltage is reached.

7.  Use the 

Surge waveform zoom

 icons to adjust the time display scale of the surge waveform.

8.  Release the 

PTT

 button after the desired number of surge pulses have been applied at the 

target test voltage level.

9.  If the winding is a wye or delta configuration, select lead 2 and repeat Steps 5–8 then repeat for 

lead 3.

NOTE

To facilitate comparison of leads, you will not be able to select different time 
scales for leads 2 and 3.

10. The results of the winding tests of a wye or delta configuration will appear, as shown below. 

Save your results at this time. Performing subsequent surge tests will overwrite the displayed 
results.

Summary of Contents for Baker DX Series





























Reviews:

No comments