1.
It usually takes around 30-60 minutes for the belt or wrapping
pad to reach the maximum temperature if you put both a thick
protector and a thick blanket on top
. Cover the belt or wrapping
pad with a blanket and leave it periodically, checking how hot it
is under the blanket.
2.
The
heating process stops and resumes again when the belt
or wraps cool down to maintain the set temperature
. During
this time, the gems become very warm and emit radiant Far
Infra-Red rays.
3.
For extra electrical safety, the heating wires are positioned
at a short distance from the amethyst pad edges so that the
end tubes with crystals are heated indirectly by other stones.
It is normal when
these close to edges stones have a lower
temperature.
4.
When the heat is on, the surface temperature of the bare belt or
wrapping pad under the blanket or under your body if you are
on the pad becomes hot to touch.
At maximum heat level, it
will reach 140-150°F (60-65°C) on the surface, if measured
immediately after you stand up or remove the thick blanket or
pillow. But if you measure the bare pad surface temperature
in several minutes again, it will be much lower, around 110-
130°F (40-50°C).
If the belt or wraps are uncovered, room
temperature is low, or the airflow is strong, it will quickly cool
the pad. This is normal – when preheated, the crystals transfer
most of the energy in Far Infrared Rays very quickly.
5.
If you keep your belt or wraps open without the protector pad,
blanket, or your body on it, the heat is dissipated – and though
the controller may continue to show rather a high temperature
inside the belt’s or hands wrap’s heating elements,
the surface
will be merely warm to touch even on the highest level.
6.
Sometimes when the belt or hands wrap starts to heat, some
humming or buzz noise can be heard from the controller, which
is quite normal. But
if the noise gets stronger or you feel any
smell or other signs of possible controller or belt or wraps
failure, please stop using the product and contact us.
7.
It is OK for the controller to warm up a little when the belt or
wraps are on the highest heat level for a long time. But it is not
normal if the controller gets hot or if you notice any smell. Please
turn off the belt or wraps and contact us for a free replacement if
this happens.
Remember not to put the controller on the belt
or wraps the heating pad, even if it is cool. It may heat up and
damage the controller.
8.
The most frequent reason for initial controller malfunction is an
incorrect order of connection.
It is necessary to connect the belt
or wrapping pad to the controller first, TIGHTLY, and only after
TIPS: USING YOUR BELT OR WRAPS
this should you plug the controller into the outlet, then turn
it on and set the timer. After this, you may set the desired
temperature. When you disconnect, turn the controller to OFF,
then disconnect the plug from the socket — and only after this
(and only if necessary), unplug the controller from the belt or
wraps.
9.
Do not disconnect the controller from the belt or wraps more
frequently than necessary
to avoid the connection becoming
loose. If you connect the controller to the power source first
(before connecting it to the belt or wraps), the safety program
will lock the controller and put it in “safe” mode. It may start
to beep or will show
OF
or other error code on the screen. To
reactivate the controller, simply reconnect it in the correct order.
10.
Choose the best position. FIR amethyst rays penetrate deep and
may awake resonant vibrations on a micro level so that even after
the session is over, the body temperature may stay elevated to
a normal level of 98.6°F for up to 8 hours which is suitable for
activity and rejuvenation. This phenomenon is described in the
European bestseller «98,6 — Ideal Body Temperature as the
Secret to Optimum Health» by famous German naturopath Dr.
Uwe. But there is also the local effect when those tissues which
are closest to the belt or wraps receive more heat. It may be
beneficial for them, but the highest levels may also cause some
issues with movement if you have stones, etc.*
11. If the product feels hard at the starting point, it is essential
to cushion it correctly and eliminate the crystals’ pressure.
Put
on top a 3-D pad and a cover included in the set of your product.
You can add several layers of bamboo, cotton sheets, or towels,
but not more than one inch thick, to make your mat even softer.
As soon as your body gets used to the crystals’ pressure, you may
choose to remove the extra layers one by one. Protectors and
towels are great for sweat absorption during heating sessions or
for moderate cushioning, but it may be better to use your mat
without any covering for high intensity. With FIR, some of the
heating rays will dissipate if you use a thicker layer on top of the
stone mat and under your body. The same applies to negative
ions, but most will still travel through. As for longer sessions,
even with covers, the product can still be too hard to sleep and
too heavy to remove from your bed every evening (especially if
you have a large size mat). A simple solution is to put a 3-4 inch
thick mattress pad on top, which is lighter and easier to handle
than the stone mat. Be aware that you can cover your product
with a thicker than a one-inch layer or a non-permeable foam
pad ONLY after the mat cools down. To avoid overheating and fire
risks, NEVER heat your product with the topper or thick layer on
it. Always remove the topper first and leave only a thin cover or a
3-D pad before turning ON the heating function.
www.MediCrystal.com
7
®
EN
