background image

 

 

 

 

 

Please read this sheet as it contains 

important information 

 

Before commencing installation please familiarise yourself to the 
equipment by reading the comprehensive installation instructions. If 
in doubt then please call 0161 233 0600. Out of hours please call 
07894 684080 or 07843 355163. 

 

It is a statutory requirement that this safety system is installed and 
commissioned to the satisfaction of the manufacturer. 
 

A commissioning certificate must be issued to the end user along 
with instructions for the operation of the equipment. 
 
As the Manufacturer Medem UK should commission this safety 
system whereupon a commissioning report will be forwarded to the 
installing agent who should provide a copy to the end user.  
 
At the point of our commissioning an individual serial number will be 
attached to the system along with a 24 help line number. Photos and 
all relevant information for the installation will then be stored on the 
Medem site database to be accessed in the event of a call on the 24 
hour help line. The warranty period for the panel and sender unit will 
then be extended to Ten years. 

 

Important 

SEC-K 

Medem (UK) Limited  
Project House, 19 Dallimore Road, 
Roundthorn Industrial Estate, 
Manchester, M23 9NX 

Tel:: +44 (0) 161 233 0600     
Fax::+44 (0) 161 233 0601      
Website: www.medem.co.uk 
e-mail:[email protected]

 

Summary of Contents for SEC-K

























Reviews: