manualshive.com logo in svg

Mecmesin MultiTest 0.5-dV, Operating Manual

Share
Download
Mecmesin MultiTest 0.5-dV Operating Manual Download Page 19

 

MultiTest

-dV 

Operating Manual 

Mecmesin

 

 19 

4.10.

 

Fitting an ELS to a Test stand 

MultiTest

-dV

 test stands with

 dV

(u) mode enabled use Mecmesin ELS devices to capture 

load readings.  

To fit an ELS to the test stand slide the load cell sideways onto the dovetail and tighten 

the grub screw (circled below in red) located in the dovetail using a suitable Allen key.  

To prevent damage, do not over-tighten the grub screw in the dovetail when a gauge 

bracket is not present. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note: 

Take care when handling low capacity  ELSs such as a  5N cell, as damage can 

easily occur from mishandling.  

It is also vital to ensure that the attached grips and fixtures do not overload the ELS. If 
in doubt, please check the weight of any addition grips and fixtures before fitting these. 

 
 
 
 

MultiTest

-dV

 Dovetail, note the grub screw circled in red 

 

Summary of Contents for MultiTest 0.5-dV





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands