Mecmesin AFTI Service And Repair Manual Download Page 42

Page: 42 / 47

AFG/AFTI Mk 4

Service and Repair Manual

Number 022-614

Issue Number: 09

Page 42 of 47

400-175-

LOAD CELL 2½N (½LB)

400-034-

LOAD CELL 5N (1LB)

400-006-S01

LOAD CELL 10N (2.2LB)

400-007-S01

LOAD CELL 25N (5LB)

400-008-S01

LOAD CELL 50N (10LB)

400-024-S01

LOAD CELL 100N (25LB)

400-107-S01

LOAD CELL 250N (50LB)

400-016-S01

LOAD CELL 500N (100LB)

900-302

AFG/BFG LOADCELL KIT 1000N

900-164-V02

2500N PINNED LOAD CELL ASSEMBLY

408-392

LOADCELL SPACER FOR 2.5-5N

329-187

4WAY HEADER 0.1 PI G'PLAT

406-410

AFG MK4 L/CELL STUD 10/32 2.5 / 5N

406-409

AFG MK4 L'CELL STUD 1/4-5/16un 1000/2500N

406-408

AFG MK4 LOADCELL STUD 10 / 500N

420-138

AFG MK4 LOADCELL STUD NUT 10 / 500N

420-316

AFG MK4 LOADCELL STUD NUT 1000 / 2500N

420-265

SCREW CAP SKT 6-32UNCx5/8"

– 2.5 / 500N

420-401

M8x23 Hex Bolt s/s

– 1000 / 2500N

408-428-F11

AFG MK4 2.5 / 500N CASE (FUTEK)

408-427-F11

AFG MK4 1000 / 2500N CASE (PARRA M8)

408-432-F11

AFTI MK4 CASE

AFG XXX N Front panel complete, comprising of;
404-159

1.000 AFG MK4 FRONT COVER PLATE

420-230

3.000 PRESS STUD M3 x 8

424-027

2.000 HEXSPACER M3 x 14 F/F MODIFIED

424-046

1.000 HEXSPACER M3 x 25 F/F MODIFIED

410-515

1.000 AFG MK4 KEYPAD

410-nnn

1.000 AFG MK4 LABEL

27. Assemblies and parts from China

2.5N and 5N load cells are from Futek, and therefore the kits for these are made up
at Mecmesin HQ UK.

Load Cell kits

CAPACITY P/N

QTY DESCRIPTION

10N

900-296

AFG/BFG LOADCELL KIT 10N

25N

900-297

AFG/BFG LOADCELL KIT 25N

50N

900-298

AFG/BFG LOADCELL KIT 50N

100N

900-299

AFG/BFG LOADCELL KIT 100N

250N

900-300

AFG/BFG LOADCELL KIT 250N

500N

900-301

AFG/BFG LOADCELL KIT 500N

1000N

900-302

AFG/BFG LOADCELL KIT 1000N

2500N

900-303

AFG/BFG LOADCELL KIT 2500N

Summary of Contents for AFTI
















































Search results

Summary of Contents for AFTI

Reviews:

Related manuals for AFTI

Brands by name

Popular brands

Mecmesin AFTI, Service And Repair Manual

Search results

Summary of Contents for AFTI

Reviews:

Related manuals for AFTI

Brands by name

Popular brands