manualshive.com logo in svg

Mecal CDA10, Use And Maintenance Manual

Share
Download
Mecal CDA10 Use And Maintenance Manual Download Page 57

 

 

CRIMP DATA ANALYZER

 

CDA10 

 

REV.01 

 

 

55 

5.2.1.2

 

STANDARD 

The operations to be carried out to connect the load cell electrically are: 

•

 

Check that the switch, located on the press or in the electrical cabinet/panel, is in the OFF (O) 
position. 

•

 

Disconnect the press from the electrical mains. 

•

 

Open the electrical box of the press. 

•

 

Intercept the cables from the load cell and BCC: white, brown, yellow, green, rose and grey. 

•

 

Connect the brown cable to the pos.4 input [+18V] on the terminal board (combined with the 
cable present). 

•

 

Connect the white cable to the pos.5 input on the terminal board (combined with the cable 
present). 

•

 

Connect the grey cable to the pos.10  input on the terminal board (combined with the cable 
present). 

•

 

Connect the green cable to the pos.12  input on the terminal board (combined with the cable 
present). 

•

 

Connect the yellow cable to the black cable with PD indication by means of the supplied clamp. 

•

 

Connect the rose cable to the black cable with PX indication by means of the supplied clamp. 

•

 

Close the electrical box with the screws. 

•

 

Connect the press to the electrical mains. 

•

 

Move the switch to the ON (I) position. 

•

 

Configure the load cell [see the relative paragraph]. 

 

 

Summary of Contents for CDA10
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands