Mecademic Meca500 R3 Programming Manual Download Page 49

Page: 49 / 110

Programming manual for Meca500 (for firmware 9.2.x)

TCP/IP COMMUNICATION

2.2.37 SyncCmdQueue

(

)

This command is used for associating an ID number with any non-motion command, thus providing

means to identify the command that sent a specific response. It it is executed immediately.

Arguments

•

: a non-negative integer number, ranging from 0 to 4,294,967,295.

Responses

[2097][

]

For example, sending

SyncCmdQueue

(123) just before the

GetStatusRobot

command allows the

application to know if a received robot status (code 2007) is the response of the

GetStatusRobot

request (i.e., preceded by [2097][123]) or of an older status request.

2.2.38 SwitchToEtherCat

This command will disable the TCP/IP, EtherNet/IP and PROFINET protocols and enable EtherCAT instead

(EtherCAT is an exclusive protocol that cannot be used at the same time as other Ethernet-based

protocols, see

Section 4

Enabling EtherCAT will disable all other communication protocols (TCP/IP, EtherNet/IP,

PROFINET).The web portal is NOT accessible while in EtherCAT mode.

There are two ways to disable EtherCAT (and thus re-enable another communication protocols):

1. Use the appropriate EtherCAT command (

Section 4.1.3

2. Perform a network configuration reset (press and hold the power button on the robot base while

the robot is rebooting (may require up to 60 seconds).

2.2.39 Tcpdump

(

)

This command starts an Ethernet capture (pcap format) on the robot, for the specified duration. The

Ethernet capture will be part of the logs archive, which can be retrieved using the Get logs option in the

web portal Options menu.

Arguments

•

: duration in seconds.

Responses

[3035][TCP dump capture started for

seconds.]

[3036][TCP dump capture stopped.]

2.2.40 TcpdumpStop

This command is needed if you want to stop the TCP dump started with the

TcpDump

(

) commands,

before the timeout period of

seconds.

Responses

[3036][TCP dump capture stopped.]

Summary of Contents for Meca500 R3















































































































Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands

Mecademic Meca500 R3, Programming Manual

Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands