Mecademic Meca500 R3 Programming Manual Download Page 66

Page: 66 / 110

Programming manual for Meca500 (for firmware 9.2.x)

TCP/IP COMMUNICATION

2.5.2 Command responses

Motion commands do not generate any (non-error) response, other than the optional EOB and EOM

messages (see Section

2.1

for details) and the message eventually generated by the

SetCheckpoint

command.

Table 3

presents a summary of all request commands and the possible non-error responses

for each of them.

COMMAND RESPONSES

Response code

Command

[2000][Motors activated.]

ActivateRobot

[2002][Homing done.]

Home

[2004][Motors deactivated.]

DeactivateRobot

[2005][The error was reset.]
[2006][There was no error to reset.]

ResetError

[2007][

eob

eom

]

GetStatusRobot

[2008][All brakes released.]

BrakesOff

[2010][All brakes set.]

BrakesOn

[2013][

]

GetWrf

[2014][

]

GetTrf

[2026][

]

GetJoints

[2027][

]

GetPose

[2028][

]

GetAutoConf

[2029][

]

GetConf

[2031][

]

GetAutoConfTurn

[2036][

]

GetConfTurn

[2042][Motion paused.]

PauseMotion

[2043][Motion resumed.]

ResumeMotion

[2044][The motion was cleared.]

ClearMotion

[2045][The simulation mode is enabled.]

ActivateSim

[2046][The simulation mode is disabled.]

DeactivateSim

[2047][External tool simulation mode has changed.]

SetExtToolSim

[2051][Requested velocity/acceleration is higher than recovery mode's

limits. Requested value will be applied automatically once the recovery

mode is disabled.]

MoveJointsVel

MoveLinVelTrf

MoveLinVelWrf

SetCartAcc

SetCartAngVel

SetCartAcc

SetJointAcc

SetJointVel

[2052][End of movement is enabled.]
[2053][End of movement is disabled.]

SetEom

[2054][End of block is enabled.]
[2055][End of block is disabled.]

SetEob

[2060][Start saving program.]

StartSaving

Summary of Contents for Meca500 R3















































































































Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands

Mecademic Meca500 R3, Programming Manual

Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands