Mecademic Meca500 R3 Programming Manual Download Page 39

Page: 39 / 110

Programming manual for Meca500 (for firmware 9.2.x)

TCP/IP COMMUNICATION

2.2.5 BrakesOn/BrakesOff

These commands engages or disengages the brakes of joints 1, 2 and 3. When the brakes are released,

the robot will fall down. This command is only available when the robot is deactivated.

Responses

[2010][All brakes set.]
[2008][All brakes released.]

2.2.6 EnableEtherNetIp

(

)

This command enables or disables EtherNet/IP slave stack, allowing the robot to be controlled by an

EtherNet/IP controller.

Arguments

•

: enable (1) or disable (0) EtherNet/IP.

default values

EtherNet/IP is enabled when the robot is shipped from Mecademic. Changes in this setting have a

persistent effect (remain even after a powering the robot off).

2.2.7 EnableProfinet

(

)

This command enables or disables PROFINET slave stack, allowing the robot to be controlled by a

PROFINET controller. Please note that enabling PROFINET also enables LLDP packets forwarding

between the two Ethernet ports of the robot.

Arguments

•

: enable (1) or disable (0) PROFINET.

default values

PROFINET is disabled when the robot is shipped from Mecademic. Changes in this setting have a

persistent effect (remain even after a powering the robot off).

2.2.8 GetExtToolfwVersion

This command returns the firmware version of Mecademic's EOAT connected to the robot's tool I/O

port. The robot must be activated. If during the activation, the robot detects that the firmware version

of the EOAT is older than the firmware version of the robot, the [3039] response will be given, and the

activation process will fail. If no EOAT is detected, the x's in the [2088] message will be zeros.

Responses

[2088][vx.x.x]
[3039][External tool firmware must be updated.]

2.2.9 GetfwVersion

This command returns the version of the firmware installed on the robot, even if the robot is not

activated.

Responses

[2081][vx.x.x]

Summary of Contents for Meca500 R3















































































































Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands

Mecademic Meca500 R3, Programming Manual

Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands