25
the VOLUME CONTROL until the Front Panel
Display indicated “SAVE PROFILE, Profile
Saved”. Refer to figure 81.
6. To exit the Profile Setup Mode momentarily
press
the VOLUME Control.
To select a previously saved Profile perform the foll-
wing steps:
7. Rotate the PROFILE Control to select from the
available Profiles stored in memory. Refer to
figure 82.
Note: The first time the PROFILE Control is
rotated, the Front Panel Display will indi-
cate the current Profile selection. Refer to
figure 83.
RENAMING A PROFILE
The MXA70 Profile Name (Profile1 thru Profile5 as
indicated on the Front Panel Display) can be custom
-
ized with a different name up to eight characters long
(Y10-PRO, etc.). The available characters for renam
-
ing the input include the following: ! < > * , / - _ 0 1
2 3 4 5 6 7 8 9 a b c d e f g h i j k l m n o p q r s t u v
w x y z A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z . In this example the previously created
and saved Profile1 will be renamed to “Y10-PRO” by
performing the follwing steps:
choices available, the correct impedance and power
output for the Headphones that will be used for
listening. Refer to figures 72 thru 78.
2. If desired, select the HXD
TM
Mode by momentarily
press the the VOLUME Control. The HXD Icon
located above the Headphone Jack will illuminate
Green. Refer to figure 71.
3. If desired, select the amount of TRIM Bass Boost
by momentarily
pressing the INPUT Control.
Then rotate the INPUT Control to select BASS
BOOST followed by using the OUTPUT Control-
for the desired increase. Refer to figures 53 and 54
on page 21.
CREATE A PROFILE
With the Impedance/Power, HXD and Bass Boost set-
tings made, they will now be assigned to Profile1, for
easy recall at a later time. The PROFILE and VOL-
UME Controls are used to perform the various Profile
Functions (Save, Select Rename and Delete). When
the PROFILE Control is rotated and there are no saved
Profiles the Front Panel Display will indicate.the cur-
rently selected Input and “NO PROFILE SAVED”.
Refer to figure 79.
Create new Profile1 by following the below steps:
4. Press and hold in the VOLUME CONTROL until
the Front Panel Display indicates “SAVE PRO-
FILE, Profile1”. Refer to figure 80.
5. To store “Profile 1” into memory press and hold in
How to Operate the MXA70, con’t
Figure 80
SAVE PROFILE
Profile1
Figure 79
INPUT: UNBAL
NO PROFILE SAVED
Figure 81
SAVE PROFILE
Profile Saved
Figure 82
INPUT: UNBAL
Profile1
8. Refering to figure 84, rotate the PROFILE Control
to select “NAME PROFILE, Profile1”.
9. Press and hold the VOLUME Control until the
the character “P” of the “Profile1” starts flashing.
Refer to figure 85.
11. Rotate the PROFILE Control until the character
“Y” appears . Then Rotate the OUTPUT Control
until the character “r” of the “Yrofile1” starts
flashing. Refer to figure 86.
12. Rotate the PROFILE Control until the character
“1” appears. Then rotate the OUTPUT until the
character “o” of the “Y1ofile1” starts flashing.
Refer to figure 87.
13. Repeat steps 9 thru 12 until the new name of
“Y10-PRO” is indicated on the Front Panel Dis-
play. Refer to figure 88.
Figure 83
INPUT: UNBAL
PROFILE NOT SET
Figure 84
NAME PROFILE
Profile1
Figure 86
NAME PROFILE
Yrofile1
Figure 87
NAME PROFILE
Y1ofile1
Figure 88
NAME PROFILE
Y10-PRO
Figure 85
NAME PROFILE
Profile1
Summary of Contents for MXA70
Page 9: ...9 Notes...
