background image

-McGaughy’s warrants all 

McGaughy’s

 products against manufacturer’s

defects in materials or workmanship for a period of 

ONE-YEAR

 from the date

of original purchase. All McGaughy’s spindles carry a 

LIFETIME

 warranty

against manufacturer’s defects.

-Warranty will not extend to any product or part there in, that has been

improperly installed, abused, or neglected

-McGaughy’s will not warranty any product(s) that were modified in any way.

Check fit all products prior to custom painting, powder-coating, or any form

of fabrication (sanding, drilling, painting, chroming, etc).

-There are 

NO WARRANTIES

 neither espressed nor implied for powder-

coating on any McGaughy’s products.

-McGaughy’s is not responsible for damages and/or warranty of other vehicle 

parts (factory or aftermarket) related or non-related to the install of

McGaughy’s component(s).

-Warranty is limited to the repair or replacement (of McGaughy’s product

only), at McGaughy’s discretion. And only after inspection of the defective

part, once returned to McGaughy’s with proof of purchase, date of purchase, 

and all shipping costs prepaid.

-Any cost of labor, freight, incidental or consequential damages are expressly

excluded from warranty.

559-226-8196

4603 E. VINE AVE.

FRESNO, CA 93725

www.mcgaughys.com

WARRANTY INFORMATION

Summary of Contents for 52370













Reviews: