manualshive.com logo in svg

McCrometer ML255, Installation, Operation And Maintenance Manual

Share
Download
McCrometer ML255 Installation, Operation And Maintenance Manual Download Page 35

MAIN MENU DESCRIPTIONS

Copyright © 2018 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. 

Any published technical data and instructions are subject to change without notice. Contact your McCrometer representative 

for current technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA 

Printed In The U.S.A.

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 

Lit. # 30122-46 Rev. 1.2 / 5-31-18

33

*MX+MN P2

MAX AND MIN PRESSURE 2 OUTPUT (ENERGISED= AL. OFF) 

*MIN P2

MIN PRESSURE 2 OUTPUT (ENERGISED= AL. OFF) 

*MAX P2

MAX PRESSURE 2 OUTPUT (ENERGISED= AL. OFF) 

*MX+MN P1

MAX AND MIN PRESSURE 1 OUTPUT (ENERGISED= AL. OFF) 

*MIN P1

MIN PRESSURE 1 OUTPUT (ENERGISED= AL. OFF) 

*MAX P1

MAX PRESSURE 1 OUTPUT (ENERGISED= AL. OFF) 

MX+MN Q

MAX AND MIN FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MX+MN Q-

MAX AND MIN NEGATIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MIN Q-

MIN NEGATIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MAX Q-

MAX NEGATIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MX+MN Q+

MAX AND MIN POSITIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MIN Q+

MIN POSITIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

MAX Q+

MAX POSITIVE FLOW RATE ALARM OUTPUT (ENERGISED=AL. OFF) 

* These outputs are not available.

Summary of Contents for ML255



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands