background image

EC DECLARATION OF CONFORMITY

 

Conforming to EEC Machinery Directive 98/37/EC*

 

 

We, 
 

McCONNEL LIMITED,

  

Temeside Works, Ludlow, Shropshire SY8 1JL. 

 
 

Declare under our sole responsibility that: 

 
The product 

(type)

 …………………………………………………………………… 

 
…………………………………………………………………………………………. 
 
Product Code ………………………………………………………………………….. 
 
Serial No. & Date ……………………………………. Type ………………………… 
 
Manufactured by the above company/* ……………………………………… 
 
…………………………………………………………………………………………. 

(* insert business name and full address if not stated above) 

 
 

Complies with the required provisions of the Machinery Directive 98/37/EC, * 
previously Directive 89/392/EEC as amended by Directives 91/368/EEC, 93/44/EEC 
and 93/68/EEC.  
The machinery directive is supported by; 

 

BS EN ISO 12100:2003  Safety of Machinery. This standard is made up of two 
parts; Part 1 Terminology, methodology, Part 2 Technical Specifications. 

 

BS EN 1050 Safety of machinery - Principles of risk assessment. 

 

and other national standards associated with its design and construction as 
listed in the Technical File. 

The Machinery Directive is fully implemented into UK law by means of the Supply of 
Machinery (Safety) Regulations 1992 (SI 1992/3073) as amended by The Supply of 
Machinery (Safety) (Amendment) Regulations 1994 (SI 1994/2063). 

 
 
 
Signed …………………………..…………………………………………………….…….. 

 

on behalf of McCONNEL LIMITED

                                                                   

Responsible Person

 

 

 

 

 

 

 

 

 

Status:

     

Chief Design  Engineer

   

 

 

 

           

Date: 

15

th

 November 2004

 

Summary of Contents for PA 48





















































Reviews: