Sealey POWER TOOLS SA25T, Instructions

Page: 1 / 2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3 Follow all workshop health & safety rules, regulations, and conditions when using tool.
p WARNING! Disconnect from air supply before changing cutting disc or servicing.
3 Maintain tool in good condition and replace any damaged or worn parts. Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
p WARNING! Before each use check cutting disc is secure, and the disc is not worn or
damaged, if damaged replace immediately.
3 Ensure replacement discs are not damaged in any way such as cracks, deformations or
splinters etc. Also check the mounting washer to ensure it is not deformed, burred or
notched. Damaged washer must not be used as it may cause irregular pressure on the disc
which may cause the disc to break. DO NOT over tighten a disc and never tamper with a disc
in order to adapt it to a different size holder.
3 Always use the correct disc suitable for the material being cut. Ensure the maximum speed
specification of the cutting disc is higher than that indicated on the machine data plate.
p WARNING! Keep disc guard in place, tight and in good working order. The safety guard is a
mandatory fitting where tool is used in premises covered by the Health & Safety at Work Act.
p WARNING! Always wear approved eye and face protection when operating the tool.
3 Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard.
3 Wear ear defenders and gloves if necessary.
3 Keep hands and body clear of the workpiece when operating the tool.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non stable work piece with a clamp, vice or other adequate holding device.
3 Keep children and non essential persons away from the working area.
3 Avoid subjecting disc to excessive strain, always ease disc down against workpiece (a harsh
impact may break the disc). Do not over press in order to cut workpiece. Maintain a controlled
adequate progression, which will emit a min imum of sparks.
8
DO NOT get the tool wet or use in damp or wet locations.
8
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
7 DO NOT use the tool for a task it is not designed to perform.
p
p
WARNING! DO NOT use tool if damaged or faulty. Contact your local service agent.
7 DO NOT use tool unless you have been instructed in its use by a qualified person.
7 DO NOT position your body in line with the disc whilst cutting, and DO NOT remove
the safety guard whilst in use.
7 DO NOT carry the tool by the air hose, or yank the hose from the air supply.
7 DO NOT direct air from the air hose at yourself or others.
p WARNING! DO NOT cut any materials containing asbestos.
SA25T - 3 - 29/03/04
INSTRUCTIONS FOR
3” AIR CUT-OFF TOOL
Model:
SA25T
01284 757500
E-mail: sales@sealey.co.uk 01284 703534
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group , Bury St. Edmunds, Suffolk.
Issue Date: 29/03/04
Version No: 3
1 SA25T/01 HOUSING
2 SA25T/02 VALVE BUSHING
3 SA25T/03 TRIGGER ASSEMBLY
4 SA25T/04 PIN
5 SA25T/05 O-RING
6 SA25T/06 O-RING
7 SA25T/07 VALVE STEM
8 SA25T/08 SPRING
9 SA25T/09 AIR REGULATOR
10 SA25T/10 O-RING
11 SA25T/11 O-RING
12 SA25T/12 VALVE PLUG
13 SA25T/13 MUFFLE COVER
14 SA25T/14 AIR INLET
15 SA25T/15 BEARING
16 SA25T/16 END PLATE
17 SA25T/17 BALL
18 SA25T/18 ROTOR
Item Part No Description Item Part No Description
19 SA25T/19 ROTOR BLADE
20 SA25T/20 CYLINDER
21 SA25T/21 WASHER
23 SA25T/23 FRONT PLATE
24 SA25T/24 PIN
25 SA25T/25 BEARING
26 SA25T/26 COLLET HOLDER
27 SA25T/27 RETAINER
28 SA25T/28 METAL DISC GUARD
29 SA25T/29 NUT
30 PTC/3C CUTTING WHEEL( NOT INCLUDED )
31 SA25T/31 WASHER
32 SA25T/32 BOLT
33 SA25T/33 WASHER
34 SA25T/34 WRENCH
35 SA25T/35 HEX WRENCH ( NOT SHOWN )