background image

 

GENUINE  PARKING SENSORS (Rear) 

INSTALLATION INSTRUCTIONS 

 

Thank you for purchasing a genuine Mazda accessory. 
Before removal and installation, be sure to thoroughly read these instructions. 
Please read the contents of this booklet in order to properly install and use the parking sensors 
(Rear). Your safety depends on it. 
Keep these instructions with your vehicle records for future reference.

 

 

 

 

 

There are several 

WARNING

 and

 

CAUTION

 sections in this booklet concerning safety when 

installing or removing the parking sensors (Rear). Always read and follow them in order to prevent 
injuries, accidents, and possible damage to the vehicle. 

 

WARNING:

 

Indicates a situation in which serious injury or death could result if the warning 

is ignored.

 

 CAUTION:

   

Indicates a situation in which bodily injury or damage to the vehicle could result if the 
caution is ignored. 

 

For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using 
a torque wrench.

 

  Do not modify the parking sensors (Rear). 

  Do not install the parking sensors (Rear) remove in any way other than described in the following 

instructions. 

  If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in 

installation. 

  If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice 

before using it. 

  Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property 

that arise from the failure of the dealer or installer to follow these instructions. 

  To ensure safety and reliability of the work, installation, removal and disposal work must be carried out 

by an Authorized Mazda Dealership. 

  Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or 

other dirt. 

 

 
 

PART NAME: 

Parking Sensors (Rear) 

VEHICLE: MAZDA 

CX-5 

PART NUMBER: 

KB7W V7 290A

 

  (Parking Sensors, Main Kit) 

 

C860 V7 281A    (Parking Sensors, Sensor Kit) 
KD33 V7 282      (Optional ON-OFF switch) 

 

 

 

 

To the dealer 

  Please turn over these instructions to the customer after installation. 

To the customer 

  Keep these instructions after installation. The instructions may be

 

necessary 

for installing other optional parts or removal of this accessory.

 

  Should the vehicle or this accessory be resold, always leave these instructions 

with vehicle for the next owner. 

NOTE 

06DE4313B

 

 

WARNING 

Summary of Contents for C860 V7 281A









































Reviews: