Mazda B-Series Training Manual Download Page 62

Page: 62 / 146

Emission System

WL-C Engine

Intake Shutter Valve

•

The WL-C engine uses a three-step ISV, which increases the EGR rate at low engine
speeds and prevents bucking movements of the engine during shut-off. The operation is
similar to the ISV used on the Mazda6 pre F/L (2.0 MZR-CD).

BT-50_01026

Fully opened at normal driving (for low
EGR rate or no EGR)

First vacuum actuator operates for high
EGR rate and shortly when the engine is
shut off

Fully closed when the engine is shut off

Second vacuum actuator operates
shortly when the engine is shut off

Slightly opened to create vacuum (for
high EGR rate)

NOTE:

Function and operation of the ISV are as described for the Denso common rail

system in the course ‘Basic Diesel Engine Management’ (CT-L2005).

01-38 Service

Training

BT-50

Summary of Contents for B-Series



















































































































































Search results

Summary of Contents for B-Series

Reviews:

Related manuals for B-Series

Brands by name

Popular brands

Mazda B-Series, Training Manual

Search results

Summary of Contents for B-Series

Reviews:

Related manuals for B-Series

Brands by name

Popular brands