manualshive.com logo in svg

Mazda B-Series, Training Manual, Page: 142 / 146

Share
Download
Mazda B-Series Training Manual Download Page 142

Instrumentation / Driver Info 

Body & Accessories 

Key Reminder Warning Alarm  

• 

This function warns with an intermittent sound from the buzzer in the IC that the key is in 
the steering lock in position ACC or LOCK when any door is opened. Additionally a 
permanent sound warns when a door is opened and the lights are switched on. 

 

Input / Output Check Mode 

• 

This function allows checking the input and output circuits of the instrument cluster. It 
can be activated in the following way: 

1.  Press and hold the odometer/tripmeter switch, and turn the ignition switch to the ON 

position.  

2.  Continue holding the odometer/tripmeter switch for approx. 5 s. until 

tESt

 is 

displayed on the LCD.  

3.  Release the odometer/tripmeter switch within 3 s after 

tESt

 is displayed.  

4. 

When the odometer/tripmeter indicates check code 00, push the odometer/tripmeter 
switch to select a check code. 

 

5. 

Inspect the check codes according to the W/M.

 

 

Check code

Check item

Related items

04

Door switch

• Key reminder warning alarm
• Lights-on reminder warning alarm

08

TNS relay

• Lights-on reminder warning alarm
• Each illumination light

09

Headlight switch

• Headlight 
• Rear fog light control system

10

Speedometer sensor

Speedometer

11

PCM

Tachometer

12

Speedometer

Speedometer

13

Tachometer

Tachometer

14

Buzzer

Buzzer

15

Rear fog light relay

Rear fog light indicator light

16

Fuel-level warning light

Fuel-level warning light

18

Engine key illumination

Engine key illumination

22

Fuel gauge sender unit

Fuel gauge

23

Fuel gauge

Fuel gauge

24

ECT sensor

Water temperature gauge

25

Water temperature gauge

Water temperature gauge

26

• Odometer/tripmeter (LCD)
• Warning and indicator lights

• Odometer/tripmeter (LCD)
• Warning and indicator lights

29

Rear fog light switch

Rear fog light control system

31

Key reminder switch

Key reminder warning alarm

40

Front fog light relay

Front fog light relay

BT-50_T09011

 

 
 

09-24 Service 

Training 

BT-50 

Summary of Contents for B-Series



















































































































































Reviews:

No comments