Mazda B-Series Training Manual Download Page 79

Page: 79 / 146

WL-C Engine

Control System

PCM Replacement

•

When the PCM has been replaced certain procedures have to be performed in the
following order:

1. Perform PCM configuration procedure.

2. Perform IMMOBILISER SYSTEM programming.

3. Perform PCM data reset procedure to reset all adaptation values in the PCM with the

aid of the M-MDS. Therefore, select the option

Toolbox

Powertrain

Data

Reset

PCM

and follow the instructions.

4. Perform After repair procedure.

5. Start the engine.

6. Turn the engine switch to the off position.

7. Turn the engine switch to the ON position (Engine off).

8. Perform KOEO self-test procedure.

9. Turn the engine switch to the off position.

10. Wait for 5 s.

11. Start the engine.

12. Perform KOER self-test procedure.

13. Turn the engine switch to the off position.

NOTE:

For further information refer to the W/M.

NOTE:

It is recommended to perform the MAF sensor learning function when a PCM data

reset has been carried out.

Service Training BT-50

01-55

Summary of Contents for B-Series



















































































































































Search results

Summary of Contents for B-Series

Reviews:

Related manuals for B-Series

Brands by name

Popular brands

Mazda B-Series, Training Manual

Search results

Summary of Contents for B-Series

Reviews:

Related manuals for B-Series

Brands by name

Popular brands