background image

GI 

SAFETY  I N FORMATION 

SAFETY  INFORMATION 

LUBRICANTS 

Avoid prolonged and repeated contact with petroleum-based oils. Used oil may irritate the skin, and can 

cause  skin  cancer and  other  skin  disorders. 

Wash thoroughly after working with  oil .  We recommend water soluble hand cleaners.  Do not use kero­

sene, 

gasoli

ne, 

or 

any  other  solvent,  to  remove  oil  from  your  skin. 

If repeated or prolonged contact with oil is necessary, wear protective clothing. Soiled clothing, particular­
ly those soiled with  used  oils and greases containing lead,  should be cleaned  at  regular i ntervals. 

4OUGIX.Q02 

JACKING  POSITIONS 

Warning 

• 

Improperly jacking a vehicle Is dangerous_ The vehicle can slip off the jack and cause serious 
Injury.  Use  only the correct front  and  rear jacking  positions and  block the wheels. 

Use  safety  stands to  support  the vehicle after  it  has  been  lifted. 

Front 

At  the center of  the crossmember 

SAFETY  STAND  POSITIONS 
Front 

Both  sides of the vehicle 

GI-2 

Rear 

At the center of the crossmember 

Rear 

Both  sides of the vehicle 

46UGIX.Q03 

Summary of Contents for 626 1994











Reviews: