Maytag CG31400ADW Service Manual Download Page 52 | Manualshive

Page: 52 / 63

background image

C–4

16023522

©2004 Maytag Services

Conversion Instructions

(Models CPL1100AD*, CGL1100AD*)

-9-

GAS CONVERSION

General

All ranges are equipped with fixed orifices and with a
convertible appliance pressure regulator. The unit model
number plate states which gas it was adjusted for at the
factory. To convert the unit to either Natural gas or LP gas
will require the replacement of orifice hoods, adjustment
of the air shutters on the burners and adjustment of the
appliance pressure regulator converter cap.

SEE INSTRUCTIONS FOR GAS CONVERSION

LOCATED ON THE BACK OF THE RANGE.

Inlet pressure to the appliance pressure regulator should
be as follows for both operation and checking of appliance
pressure regulator setting:

INLET PRESSURE IN

NATURAL

LP

INCHES OF WATER COLUMN

GAS

GAS

Minimum

5

11

Maximum

14

14

HOW TO REMOVE RANGE
FOR SERVICING

Follow these procedures to remove appliance for
servicing:

1. Shut off gas supply to appliance.

2. Disconnect electrical supply to appliance, if equipped.

3. Disconnect gas supply tubing to appliance.

4. Slide range forward to disengage range from the

anti-tip bracket. (See page 4).

5. Reverse procedure to reinstall. If gas line has been

disconnected, check for gas leaks after reconnection.

NOTE:

A qualified servicer should disconnect and

reconnect the gas supply.

The servicer

MUST

follow installation instructions

provided with the gas appliance connector and the
warning label attached to the connector.

6. To prevent range from accidentally tipping, range must

be secured to the floor by sliding rear leveling leg into
the anti-tip bracket.

SERVICE - PARTS INFORMATION

WHEN YOUR RANGE REQUIRES SERVICE OR
REPLACEMENT PARTS, CONTACT YOUR DEALER
OR AUTHORIZED SERVICE AGENCY. PLEASE GIVE
THE COMPLETE MODEL AND SERIAL NUMBERS OF
THE RANGE WHICH IS LOCATED ON THE RANGE
MODEL NUMBER PLATE.

«
...
50
51
52
53
54
...
»

Summary of Contents for CG31400ADW
































































Reviews:

No comments

Related manuals for CG31400ADW

Brand: Mackie Pages: 4

Brand: S&B Filters Pages: 13

Pro-Finish 2636

Brand: Empire Pages: 57

Brand: Jarrett Pages: 10

HighLine Classic LED daylight 70

Brand: Oase Pages: 129

Brand: PALSON Pages: 1

mega macs 42 SE Bike

Brand: GUTMANN Pages: 53

Kapriol SP series

Brand: Sirmex Pages: 27

Brand: Eaton Pages: 76

Brand: Aquatronica Pages: 19

Brand: Crestron Pages: 52

Digitrip OPTIM 550 KEP3125T52

Brand: Eaton Pages: 10

Brand: Ferplast Pages: 32

Brand: Ferplast Pages: 50

Brand: Ferplast Pages: 52

Brand: Ferplast Pages: 52

Brand: Icom Pages: 2

ANOFRAME ROUND WITH WINDOW MOUNTS

Brand: ROSE DISPLAYS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands