Maytag CG31400ADW Service Manual Download Page 15

Page: 15 / 63

Component Testing Procedures

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power and gas to oven before servicing,
unless testing requires power and/or gas.

16023522

Illustration Component

Test

Procedure

Results

GND

L or N

Input

Spark module
4 + 0

Test for voltage at terminals

L and N...............................................

Polarity and ground ............................

120 VAC

Not subject to polarity

Spark module
2 + 0
CGL1100AD*

Test for voltage at terminals...................

Polarity and ground................................

120 VAC

Not subject to polarity

Holder orifice

Verify gas pressure (WCP) ....................

Check orifice for debris ..........................

Natural

LP/Propane

Clean as needed.

Shut-off Valve

Verify gas supply is turned on.

Gas is turned on.

Shut-off Valve
Model CPL1100AD*

Verify gas supply is turned on.

Gas is turned on.

270

valve

Verify gas is supplied.
Orifice adjusted for Natural or LP.

Adjust set screw for simmer control .......

Refer to LP/Nat. conversion instructions.

Spark 270

switch

Unplug switch harness at rear of
range. Test for continuity at wire
terminals.

Switch in LITE position .........................
Switch in any other position..................

120 VAC

Continuity
Infinite

Spark switch
Model CGL1100AD*

Unplug switch harness at rear of
range. Test for continuity at wire
terminals.

Switch in LITE position .........................
Switch in any other position..................

120 VAC

Continuity
Infinite

Sealed burner

Verify gas is supplied .............................
Check for obstructions or
contamination in burner ports.................

Gas present.

Clean/remove any foreign objects.
Check ignitor for bending/cracking.

Open burner
Model CPR1100AD*,
LPR1115AD*,
CP31200AD*,
CG31200AD*

Verify gas is supplied .............................

Verify air shutter adjusted properly.........

Gas present.

Air shutter opening: .400" to .500".

Open burner
Models CPL1100AD*,
CGL1100AD*

Verify gas is supplied .............................

Verify air shutter adjusted properly.........

Gas present.

Air shutter opening: .435" to .565".

Open burner
Model CGR1110AD*

Verify gas is supplied .............................

Verify air shutter adjusted properly.........

Gas present.

Air shutter opening: .420" to .460".

Pilot burner
Models CPL1100AD*,
CPR1100AD*,
LPR1115AD*,
CP31200AD*,
CG31200AD*

Verify pilot selector cartridge is set to
the proper gas........................................

LP or Natural

Summary of Contents for CG31400ADW
































































Search results

Summary of Contents for CG31400ADW

Reviews:

Related manuals for CG31400ADW

Brands by name

Popular brands

Maytag CG31400ADW, Service Manual

Search results

Summary of Contents for CG31400ADW

Reviews:

Related manuals for CG31400ADW

Brands by name

Popular brands