manualshive.com logo in svg

Maytag AMV1162AAB/W/Q/S, Service

Share
Download
Maytag AMV1162AAB/W/Q/S Service Download Page 54

A – 14

16023056   Rev. 0

©2004 Maytag Services

Installation Instructions

17

STEP 6:

Attach The Oven To The Wall

1. Carefully lift microwave oven and hang it on support tabs (See

Figure 26 at the bottom of the mounting plate.) Reaching
through upper cabinet, thread power supply cord through the
power supply cord hole in the bottom of the upper cabinet. See
Figure 30.

2. Rotate the microwave oven upward so the top of oven is

against the bottom of the upper cabinet or cabinet frame.

To avoid risk of personal injury or property damage, you will need two people to
install this microwave oven.

W A R N I N G

Figure 30

Figure 31

power cord

power cord
hole

Insert a bolt down through each hole in the upper cabinet 
bottom. See 

Figure 31. 

Tighten the bolts until the gap between the upper 
cabinet and microwave oven is closed.

3. 

4.  If wall vented or room vented installation is used, go to 

No.7 on the next page.

Summary of Contents for AMV1162AAB/W/Q/S


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands