Maytag AMV1162AAB/W/Q/S Service Download Page 45

Page: 45 / 57

16023056 Rev. 0

A – 5

Installation Instructions

pqbm NW

m~ q b~ `

^slfa bib`qof`^i pel`h> qefp ^mmif^k`b jrpq _b dolrkaba>

1. Locate the grounded electric outlet for this oven in the

cabinet above the oven, as shown in Figure 4.

klqbW

The outlet should be on a circuit dedicated to the

microwave oven (120V, 60 Hz., AC only) with a 15 or 20A
fused electrical supply.

fjmloq^kqW

If you do not have the proper wall outlet,

you MUST have one installed by a qualified electrician.

2. You will cut the power-supply-cord hole (shown in Figure 4)

later when you prepare the wall and upper cabinet in Step 4.

klqbW

Do not use an extension cord.
Keep the power cord dry and do not pinch or crush it.

t ^ o k f k d

f ~ K

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD
GROUNDING PRONG!

This appliance MUST be grounded!

r

`~

mJpJ` e

d l

(Inside Cabinet)

c Q

t ^ o k f k d

Summary of Contents for AMV1162AAB/W/Q/S


























































Search results

Summary of Contents for AMV1162AAB/W/Q/S

Reviews:

Brands by name

Popular brands

Maytag AMV1162AAB/W/Q/S, Service

Search results

Summary of Contents for AMV1162AAB/W/Q/S

Reviews:

Brands by name

Popular brands