manualshive.com logo in svg

Maytag AMV1162AAB/W/Q/S, Service

Share
Download
Maytag AMV1162AAB/W/Q/S Service Download Page 48

A – 8

16023056   Rev. 0

©2004 Maytag Services

11

To avoid risk of property damage, unplug the microwave oven or disconnect power at
source by removing fuse or throwing circuit breaker.

To avoid risk of personal injury, wear protective gloves when handling mounting plate.

STEP 3:

 Prepare The Venting Blower

Before You Start

1. Remove any shipping materials and parts from inside the

microwave oven.

2. Cover the counter top or cooktop with a thick, protective

covering to protect it from damage and dirt. See Figure 10.

NOTE:

If you have a free-standing range, disconnect it, move it
onto a piece of cardboard or hardboard and pull it away
from the wall, so that you can get closer to the upper
cabinet and back wall for easier measuring and drilling.

Remove The Mounting Plate:

1. Remove mounting plate screw(s) (1 or 2 screws) from the

mounting plate as shown and discard. See Figure 11.

2. This plate will be used as the rear mounting plate. (It will be

used to locate and mark the mounting holes on the rear wall.)

3. Locate exhaust adaptor, grease filters and hardware packet.

4. At this point, remove any adhesive tape (if there is any), on the

exhaust adaptor, the grease filters and the power supply cord.

Room-Vented 

(recirculating)

 

Installation:

This oven is shipped assembled for room-vented.

Wall-Vented Installation:

1. Remove one blower unit mounting screw and one or two

blower plate screw(s). Remove the blower plate from cabinet.
See Figure 12.

2. Carefully lift the blower unit out of the microwave oven.

3. Use side cutters or thin snips to cut and remove parts “B”

from Back plate. Discard parts "B". Be careful not to distort
the plate. See Figure 13.

DO NOT PULL OR STRETCH THE BLOWER WIRING!

Pulling and stretching the blower wiring could result in electrical

shock.

Your microwave oven is shipped with the blower assembled for room (recirculating) venting. 
If you want wall - venting or roof venting installation, you must change the blower, as detailed below.

Figure 10

Figure 11

Figure 12

Figure 13

A thick, protective

covering

Mounting plate

Mounting plate
screw(s)
(1 or 2 screws)

Control Panel Side

Mounting plate

Mounting plate
screw(s)
(1 or 2 screws)

Control Panel Side

Knock out Parts “B”

Parts “B”

Parts “B”

Blower Unit

Blower Plate Screw

Blower Plate

Back Plate

Blower Unit
Mounting Screw

W A R N I N G

Installation Instructions

Summary of Contents for AMV1162AAB/W/Q/S


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands