manualshive.com logo in svg

Maytag AMV1162AAB/W/Q/S, Service

Share
Download
Maytag AMV1162AAB/W/Q/S Service Download Page 38

Disassembly Procedures

To avoid the risk of electrical shock, personal injury or
death; disconnect power to oven and discharge
capacitors before following any disassembly procedure.

38

16023056  Rev. 0

©2004 Maytag Services

W AR NIN G

!

Magnetron

Magnetron is mounted on the side of the cavity to
provide a top feed single waveguide.

1. Disconnect power to oven and remove grille, (see

"Grille" procedure).

2. Remove control panel, (see "Control Panel"

procedure).

3. Remove outer case, (see "Outer Case" procedure).
4. Discharge high voltage capacitor, (see "High Voltage

Capacitor" procedure).

5. Remove screws securing magnetron to the wave

guide.

6. Carefully remove the magnetron.
7. Reassemble in reverse order.

Magnetron

Models UMV1152B**, MMV1153A**, AMV1162A**,

AMV5164A**

Magnetron

Models UMV1152B**, MMV1153A**, AMV1162A**,

AMV5164A**

Magnetron

Models MMV5165A**, MMV5207A**, JMV8208A**

NOTE:

When replacing the magnetron, make sure the

gasket is in the correct position and in good condition.

CAUTION

!

During replacement of magnetron, be certain the R.F.
anode gasket is in place around anode stud.

W A R N IN G

!

A microwave leakage test must be performed anytime
a magnetron assembly is removed, replaced,
disassembled or adjusted for any reason.

Magnetron Fan Assembly

Magnetron fan motor provides cool air circulation from
an external air source, which provides direct cool air
through air vanes surrounding the magnetron. This
assembly is located above the magnetron.

Magnetron Fan Removal

1. Follow steps 1 through 4 of "Magnetron" procedure.
2. Remove fan blade from fan motor.
3. Remove screws securing fan motor to air duct.
4. Disconnect wires from fan motor, and lift fan motor

assembly out.

5. Reassemble in reverse order.

Summary of Contents for AMV1162AAB/W/Q/S


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands