background image

14

The  integrated  control  module  humidifier  terminal  120V 

HUM-H  is  energized  with  115  volts  whenever  the  induced 

draft blower is energized. This terminal can also be used to 

provide 115 volt power to a humidifier transformer. The re

-

maining primary transformer wire would be connected to the 

Line N on the control board. The integrated control module 

electronic air cleaner terminals EAC-H is energized with 115 

volts whenever the circulator blower is energized. 

NOTE: Wire routing must not interfere with circu

-

lator blower operation, filter removal, or routine 

maintenance.

PCBBF145

CONTROL BOARD

EAC-H

120 HUM-H

EAC-N

120V HUM-N

115 VAC EAC

115 VAC HUM

Connecting Line Voltage Accessories

Connection of 24 Volt Humidifier

The integrated control module single humidifier terminal “24 

VHUM” is energized with 24 volts whenever the induced draft 

blower is energized. Connect the common side of the 24 volt 

humidifier to the “C” terminal of the thermostat terminal strip 

on the control board.

PCBBF145

Y/Y2 W R G C

24VHUM

24 VOLT HUM. & 

HUMIDISTAT 

Twinning

Furnaces may be twinned without the use of a twinning 

kit. Furnaces must be the same model and equipped with 

PCBBF145 control boards. Follow the diagram provided in 

this manual. Connection of the “twin” terminals of each con-

trol together will allow simultaneous operation of two or more 

furnace indoor blowers to operate synchronously on a com-

mon duct system. Field installed low voltage thermostat wir-

ing, 3/16” terminals are required to make this connection. An 

isolating relay (24 VAC coil & N/O SPST) contacts is also re-

quired if the furnaces are not fed from the same line voltage 

phase. A pulsing DC signal is used to share the call for fan 

operation between furnaces. The duration of the pulse width 

determines the speed that the reading control will energize 

its blower motor. 

CAUTION

To prevent unreliable operation or equipment damage, the 

gas manifold pressure must be as specified on the unit rating 

plate. Only minor adjustments should be made by adjusting 

the gas valve pressure regulator.

WARNING

Possible property damage, personal injury or death may 

occur if the correct conversion kits are not installed. The 

appropriate kits must be applied to ensure safe and proper 

furnace operation. All conversions must be performed by a 

qualified installer or service agency.

GAS SUPPLY AND PIPING

The furnace rating plate includes the approved furnace gas 

input rating and gas types. The furnace must be equipped to 

operate on the type of gas applied. This includes any con-

version kits required for alternate fuels and/or high altitude.

NOTE: Do no remove the gas valve inlet plug be

-

fore the gas line is installed. Replace if water or 

debris has been introduced.

CAUTION

To prevent unreliable operation or equipment damage, the 

inlet gas supply pressure must be as specified on the unit 

rating plate with all other household gas fired appliances 

operating.

Inlet gas supply pressures must be maintained within the 

ranges specified in the following table. The supply pressure 

must be constant and available with all other household gas 

fired appliances operating. The minimum gas supply pres

-

sure must be maintained to prevent unreliable ignition. The 

maximum must not be exceeded to prevent unit overfiring.

Natural Gas

Minimum:  4.5" w.c.

Maximum: 10.0" w.c.

Propane Gas Minimum: 11.0" w.c. Maximum: 13.0" w.c.

INLET GAS SUPPLY PRESSURE

NOTE: Adjusting the minimum supply pressure 

below the limits in the above table could lead to 

unreliable ignition. Gas input to the burners must 

Summary of Contents for Amana CES80 Series









































Reviews: