Maxwell MW-1756, Manual Instruction

Page: 9 / 24

9
ENGLISH
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
•
Close supervision is necessary when chil-
dren or disabled persons are near the oper-
ating unit.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience
or knowledge if they are not under supervi-
sion of a person who is responsible for their
safety or if they are not instructed by this
person on the usage of the unit.
•
Do not leave children unattended to prevent
them from using the unit as a toy.
•
If the power cord is damaged, it should
be replaced with a similar cord with corre-
sponding specifications of electrical con-
ductor profile stated on the outer isolation
of the cord.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Transport the unit in the original packag-
ing only.
•
Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature, keep it for at least three hours
at room temperature.
There may be water spots in the thermopot, this
is normal, as the unit has undergone factory
quality control.
•
Unpack the thermopot; remove any adver-
tising stickers that can prevent the unit oper-
ation.
•
Check the unit for damages, do not use it in
case of damages.
•
Make sure that the unit operating voltage
corresponds to the voltage of your mains.
•
Place the thermopot on a dry flat surface
keeping at least 20 cm gap between the
thermopot body and the wall or furniture and
at least 30 cm gap above the thermopot.
•
Open the lid (7) by pressing the front part of
the button (6) and holding it.
•
Fill the thermopot with water using a suit-
able bowl, do not exceed the maximal water
level mark «FULL» on the inner surface of the
thermopot flask.
•
Insert the power cord (15) connector into
the socket (13) on the thermopot body, and
the power cord (15) plug into the mains
socket.
•
The boiling mode indicator «Boiling» (4) will
light up on the control panel.
•
After water starts boiling, the thermopot will
be switched to the keep warm mode, the
indicator (4) will go out and the indicator (5)
“Keep warm” will light up.
Note: - the thermopot uses a long boiling tech-
nology which allows to significantly reduce the
chlorine level in water.
•
Drain the water; to do this set the lock (9)
to the position « » and press on the hand
pump (8).
Attention! Be careful while draining the water
to avoid getting burns by hot water.
•
Lock the hand pump by setting the lock (9)
to the position « ».
•
Switch the thermopot off, to do this dis-
connect the power cord (15) plug from the
mains socket and disconnect the power
cord (15) connector from the socket (13).
•
Open the thermopot lid (7) and wait until it
cools down completely.
•
To remove the lid (7) open it at 90° and pull
the lid (7) upwards taking it by both sides.
•
Carefully tilt the thermopot to drain the
remaining water.
•
Install the lid (7) back to its place, to do this
set the lid (7) vertically and press on the bot-
tom part of the lid from the left and the right
until the axis lock clicking. Before using the
thermopot make sure that the lid (7) is fixed
properly.
USAGE OF THERMOPOT
•
Open the lid (7) by pressing the button (6)
and holding it.
•
Fill the thermopot with water using a suit-
able bowl, do not exceed the maximal water
level mark «FULL» on the inner surface of the
thermopot flask.
MW-1756.indd 9 8/28/19 4:55 PM