background image

7

      866.4.Maxtec    www.maxtec.com

2.4.3 Changing Oxygen Settings

Warning: 

Adjusting the oxygen setting too high at low flows may cause 

oxygen to exit the air inlet port. Verify the direction of flow by placing your 
hand under the air filter to feel for air escape.

2.5 Disposables

The MaxVenturi for is intended for use with approved disposables. Several patient 
delivery circuits and patient interfaces have been tested and approved for use with 
the MaxVenturi. The approved delivery circuits and patient interfaces are:

2.5.1 Disposable Patient Circuits

» Fisher & Paykel single heated limb circuit (RT202) with humidifier chamber (MR290).

» Airlife single heated limb circuit (RT600-850) with humidifier chamber (MR290).

» Standard 6', 22mm corrugated tube (Airlife 001450 or similar. Not humidified).
» Comfort Flo

®

 Circuits (2415 & 2416) with the ConchaSmart

®

 Column (382-10). 

2.5.2 Disposable Patient Interfaces

» Optiflow large nasal cannula (Fisher & Paykel OPT544).

» Optiflow medium nasal cannula (Fisher & Paykel OPT846).

» Optiflow Tracheostomy direct connection (Fisher & Paykel OPT570).

» Pediatric aerosol mask with 22mm inlet (Airlife 001263 or similar).

» Adult aerosol mask (Airlife 001206 or similar).

» Trach adaptor T-piece (Airlife 001500 or similar).

» Tracheostomy mask with 22mm inlet - loose fitting (Airlife 001225 or similar).
» Hudson RCI

® 

Trach-Flex

 PlusTracheostomy Adapter (2415-01).

» Hudson RCI

® 

Comfort Flo

®

 Plus Cannula - Large (2412-11).

» Hudson RCI

® 

Comfort Flo

®

 Plus Cannula - Medium (2412-12).

» Hudson RCI

® 

Comfort Flo

®

 Plus Cannula - Small (2412-13).

CAUTION: 

Use of patient circuits or patient interfaces other than these constitutes 

"off- label use". This can result in device malfunction or harm to the patient.

The delivery circuit can be paired with the patient interface circuits listed in 

the table below:

 

1

2

 

1

2

!

Adjust O

2

% knob to desired level and 

wait for analyzer to equilibrate.

Temporarily 

disconnect patient circuit if necessary.

Verify flow rate has not changed and 
adjust if necessary.

Summary of Contents for MaxVenturi R211P03






















Reviews: