manualshive.com logo in svg

MaxLinear XR17V358, Manual, Page: 24 / 71

Share
Download
MaxLinear XR17V358 Manual Download Page 24

TIMERMSB Register

Bit-15   Bit-14   Bit-13   Bit-12   Bit-11   Bit-10    Bit-9   Bit-8

TIMERLSB Register

 Bit-7     Bit-6     Bit-5     Bit-4     Bit-3     Bit-2    Bit-1  Bit-0

16-Bit Timer/Counter Programmable Registers

XR17V358

 

24

HIGH PERFORMANCE OCTAL PCI EXPRESS UART

REV. 1.0.6

REGA [15:8] Register

Reserved.

TIMERCNTL [7:0] Register

The bits [3:0] of this register are used to issue commands. The commands are self-clearing, so reading this 
register does not show the last written command. Reading this register returns a value of 0x01 when the Timer 
interrupt is enabled and there is a pending Timer interrupt. It returns a value of 0x00 at all other times. The 
default settings of the Timer, upon power-up, a hardware reset or upon the issue of a ’Timer Reset’ command 
are:

■

Timer Interrupt Disabled

■

Re-triggerable mode selected

■

Internal 125 MHz clock (master) or 62.5 MHz clock (slave) selected as clock source

■

Timer output not routed to MPIO[0]

■

Timer stopped

T

ABLE

 9: TIMER CONTROL R

EGISTERS

TIMERCNTL [7:4] Reserved

TIMERCNTL [3:0] These bits are used to invoke a series of commands that control the function of the Timer/Counter. 

The commands 1100 to 1111 are reserved.
0001:   Enable Timer Interrupt
0010:   Disable Timer Interrupt
0011:   Select One-shot mode
0100:   Select Re-triggerable mode
0101:   Select Internal 125 MHz clock (master) or 62.5 MHz clock (slave) as clock input for the Timer
0110:   Select External Clock input through the TMRCK pin for the Timer
0111:   Route Timer output to MPIO[0] pin
1000:   De-route Timer output from MPIO[0]
1001:   Start Timer
1010:   Stop Timer
1011:   Reset Timer

Summary of Contents for XR17V358








































































Reviews:

No comments