Maxcess MAGPOWR DTR-65 Installation And User Manual Download Page 8 | Manualshive

Page: 8 / 45

background image

2–3

SAFETY INSTRUCTIONS

www.maxcessintl.com

MAGPOWR DTR-65

MI 850A349 1 D

Basic safety
information

Proper use

The digital load cell amplifier is intended to be used on machines
or systems to amplify the signal from MAGPOWR or competitor load
cells.

Indoor operation, see environmental specifications.
Improper use

Operation outside the technical specifications

Operation in an Ex-area or intrinsically safe area

Outdoor operation

Any other use than the proper use shall be deemed inappropriate
Installation and commissioning

Any digital load cell amplifier which is damaged must not be
installed or put into operation.

Only perform installation, maintenance or repair tasks on the digital
load cell amplifier when the machine into which the DTR-65 is
installed has been stopped and is secured from being turned on.

Only perform installation, maintenance or repair tasks on the digital
load cell amplifier when there is no electrical power in the system.

The digital load cell amplifier must be securely mounted before
being placed in operation.

Only replacement parts obtained from Maxcess may be used.

No modifications may be made to the digital load cell amplifier.

Do not place electrical cables under mechanical strain.

continued

«
...
6
7
8
9
10
...
»

Summary of Contents for MAGPOWR DTR-65














































Reviews:

No comments

Related manuals for MAGPOWR DTR-65

Brand: Harman Pages: 2

Brand: Harley Benton Pages: 12

Brand: R&R Ampflication Pages: 16

Brand: Xaoc Devices Pages: 6

Brand: Teac Pages: 15

Brand: VINCENT Pages: 48

Brand: XINDAK Pages: 10

Brand: Signal Pages: 16

Brand: B&K Pages: 16

Brand: McIntosh Pages: 2

L-RF-EDFA-14dBm

Brand: Questtel Pages: 16

Stereo 25 MK II

Brand: icon Audio Pages: 8

Street Sweeper MkII

Brand: SCIENCE Pages: 14

Brand: Inter-m Pages: 10

Brand: Goldmund Pages: 14

Brand: icon Audio Pages: 10

Brand: Peavey Pages: 50

Brand: M-system Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands