background image

14

4. NEVER USE THE MACHINE IN AN 

UNSTABLE PLACE.

Never use it in a place where it could move 
or fall of itself.
Be sure to install the compressor on a flat 
floor, with leg rubber underneath it; the al-
lowable tilt angle of the floor is up to 10 de-
grees.  If the installation floor is tilted and 
slippery, ensure that the compressor does 
not move during operation.  Do not use it on 
a shelf or a stand where it may fall or tumble.

5. USE THE MACHINE IN THE APPROPRIATE 

DIRECTION.

Install it appropriately.

6. NEVER INSTALL THE MACHINE IN THE 

RAIN OR IN A PLACE SPLASHED WITH 
WATER OR EXPOSED TO HIGH TEMPER-
ATURE.

Using it in the wet condition could cause an 
electric shock or a short-circuit, resulting in a 
fire due to burnout or ignition.

7. AVOIDING A PLACE EXPOSED TO HIGH 

TEMPERATURE OR THE DIRECT SUN-
SHINE, BE SURE TO USE THE MACHINE 
IN THE WELL-VENTILATED SHADE.

Using it under high temperature or in the di-
rect sunshine not only deteriorates its dura-
bility, but increases the temperature of the 
main body, causing danger to your safety.  
Be sure to use it in the well-ventilated shade. 
The adequate room temperature is +5°C to 
+30°C (41°F to 86°F). Maximum is 0°C to 
+40°C (32°F to 104°F).

8. NEVER BLOCK A VENTILATION OPEN-

ING OR USE THE MACHINE IN A BOX OR 
A NARROW PLACE(IN A VEHICLE, ETC.)

Neglect of this may generate abnormal heat, 
causing a trouble or an accident.
Install the compressor at the distance of 1 m 
or more from the wall to secure sufficient 
ventilation and cooling.

9. DO NOT USE THE COMPRESSOR IN ANY 

PLACE WHERE THE TEMPERATURE IS 
0°C (32°F) OR LESS OR THE AMBIENT 
TEMPERATURE E40°C (104°F).

Summary of Contents for AKHL1260E Powerlite
























Reviews: