Max-Thrust MAX TRAINER Balsa Pro-Built Series Manual Download Page 2

2

2

Warning:

This radio controlled model is not a toy.  It requires skill to fly and is not recommended for use by 

beginners without assistance from an experienced model pilot. It should not be operated by children 

without the supervision of a suitably experienced adult.

Max-Thrust reserves the right to modify the specification of this model at any time.

Safety Precautions

1. Do not attempt to repair or modify this aircraft with non-factory parts.

2. Never fly this model over roads, railway lines, near to power lines, airports, do not fly this model in 

excessively strong winds, in the rain, or thunderstorms.

3. Do not fly or launch the model towards people.

4. Keep hands and face away from rotating propeller at all times.

5. We strongly recommend that all fixings and fasteners used in the construction of this model are       

checked regularly for integrity.  Failure to do so could cause a crash, injury to yourself or others  around 

you.

6. We only recommend the use of 2.4GHz radio equipment with this model.

Disclaimer

1.  This radio controlled model is not a toy. Used incorrectly it is capable of inflicting serious injury to 

persons or damage to property. The owner/pilot assumes all responsibility for any damage to persons or 

property resulting from the use of this product.

2. The manufacturer and distributor decline all responsibility for any liability arising from use of this 

product.

3. It is very important that you follow all instructions for assembling and setting up of this model. Failure to 

do so could result in a loss of control and possibly a crash

Statement

Summary of Contents for MAX TRAINER Balsa Pro-Built Series

















Reviews: