background image

26

Setting for Brush motor with tachogenerator

In this configuration, the drive must set with the following solder bridges and below internal set-
ting:

RDT resistor calculations

To calculate RDT resistor, please use the following formula:

RDT (Kohm) = Kdt * N * 9,7

                        1000 * Vref

Example: Brush DC motor with the tachogenerator costant Kdt=10V/KRPM, max. speed 2500RPM 
at 10V of speed reference. The result is below:

RDT (Kohm) = 10 * 2500 * 9,7

                                1000 * 10

Insert the commercial value resistance 18Kohm. Prefer resistance with 1% tolerance.

Note:
RDT is the value of resistor expressed in Kohm with a power rating of 1/8 or 1/4w.
Kdt is the tachogenerator costant V/KRPM.
N is the max speed express in RPM.
Vref is the max v/-VEL reference express in Volts.

Once the resistor RDT is inserted, proceed with final speed adjustment.
Operate using trimmer SPEED on the front of the drive. With Clockwise Rotation the speed increases.
With Counter Clockwise Rotation the speed decreases. The Range of regulation is about +/- 25%.











SOLDER BRIDGES

In this configuration, the drive must set with the following solder bridges and below internal setting:

Solder Bridges set for:

- Tachogenerator feedback

- Ramp time disabled

- Standard Dynamic constant

ADJUSTEMENT ZONE

Note: On the adjustement zone are not considered

here the other components used to determine other

calibrations "for example. Calibration current rating

etc.".

RDT (Kohm) =  Kdt * N * 9,7

1000 * Vref

- 7,9

Example: Brush DC motor with the tachogenerator costant Kdt=10V/KRPM, max. speed 2500RPM at

10V of speed reference. The result is below:

RDT (Kohm) =  10 * 2500 * 9,7

1000 * 10

- 7,9 =  16.4 Kohm

Insert the commercial value resistance 18Kohm. Prefer resistance with 1% tolerance.

Note:

RDT

 is the value of resistor expressed in Kohm with a power rating of 1/8 or 1/4w.

Kdt

 is the tachogenerator costant V/KRPM

N

 is the max speed express in RPM.

Vref

  is  the max v/-VEL reference express in Volts.

To calculate RDT resistor, please use the following formula:

Once the resistor 

RDT

 is inserted, proceed with final speed adjustment.

Operate using trimmer SPEED on the front of the drive. With Clockwise Rotation the speed increases.

With Counter Clockwise Rotation the speed decreases. The Range of regulation is about +/- 25%.



- 7,9

- 7,9 = 16.4 Kohm

Summary of Contents for MDCA 100





































Reviews: