background image

Mass Combi Pro 12/3000-150, 24/3500-100 

– User and Installation Manual 

 

 

1  GENERAL INFORMATION 

 

1.1 

Product description 

The Mass Combi Pro is a multifunctional charger inverter. It 
passes  through  power  from  an  external  AC source  (e.g.  a 
generator or shore power connection) to your AC loads and 
charges your main batteries. 
 

1.2 

Use of this manual 

This  manual  serves  as  a  guideline  for  the  safe  and 
effective  use  and  installation  of  the  Mass  Combi  Pro,  also 
called Combi Pro further in this manual: 

  For  the  installer  this  manual  gives  directions  for  the 

installation, operation and commissioning. 

  For  the  end  user  this  manual  gives  directions  for  the 

operation,  maintenance  and  possible  correction  of 
minor malfunctions. 

  Every  person  who  works  with  the  device  should  be 

familiar  with  the  contents  of  this  manual,  and  must 
carefully follow the instructions contained herein. 

  Store the manual in an accessible place. 

 

1.3 

Validity of this manual 

This manual is valid for the following models:  
 

Part no 

Model 

38513000  

Mass Combi Pro 12/3000-150 

38523500  

Mass Combi Pro 24/3500-100 

 
All the specifications, provisions and instructions contained 
in  this  manual  apply  solely  to  the  Mastervolt-delivered 
standard version of a single Mass Combi Pro. 
 

1.4 

Liability 

Mastervolt can accept no liability for: 

 

Consequential  damage  resulting  from  the  use  of  the 

Mass Combi Pro. 

 

Possible  errors  in  the  included  manual  and  the 

consequences of these.  

 

Use  that  is  inconsistent  with  the  purpose  of  the 

product. 

1.5 

Warranty 

Mastervolt  assures  the  product  warranty  of  the  Mass 

Combi  Pro  during  two  years  after  purchase,  on  the 

condition that the product is installed and used according to 

the instructions in this manual. 

Installation  or  use  not  according  to  these  instructions  may 

result  in  under  performance,  damage  or  failure  of  the 

product and may void this warranty. The warranty is limited 

to  the  cost  of  repair  and/or  replacement  of  the  product. 

Costs of labor or shipping are not covered by this warranty. 

 

1.6 

Disclaimer 

Our  products  are  subject  to  continual  development  and 

improvement.  Therefore,  additions  or  modifications  to  the 

products  may  cause  changes  to  the  technical  data  and 

functional specifications. No rights can be derived from this 

document.  Please  consult  our  most  current  Terms  & 

Conditions of Sale. 

 

1.7 

Changes to the Mass Combi Pro 

Changes  to  the  Mass  Combi  Pro  may  be  carried  out  only 
after obtaining the written permission of Mastervolt. This is 
not  applicable  for  DIP-switches  which  are  used  for  user 
settings. 
 

1.8 

Identification label 

 

 

 

Figure 1-1: Example of an identification label 

 
The identification label is positioned at the right side of the 
Mass Combi Pro, see figure 1-1. 

 

CAUTION! 

Never  remove  the  identification 

label. 

 

1.9 

Correct disposal of this product  

 

This 

product 

is 

designed 

and 

manufactured  with  high  quality  materials 
and  components,  which  can  be  recycled 
and  reused.  When  this  crossed-out 
wheeled  bin  symbol  is  attached  to  a 
product,  it  means  the  product  is  covered 
by the European Directive 2012/19/EU.  

Please  be  informed  about  the  local  separate  collection 
system for electrical and electronic products.  
Please act according to your local rules and do not dispose 
of  your  old  products  with  your  normal  household  waste. 
The  correct  disposal  of  your  old  product  will  help  prevent 
potential  negative  consequences  to  the  environment  and 
human health. 

Summary of Contents for MASS COMBI PRO 12/3000-150





























Reviews: