Mastervolt CHARGEMASTER PLUS 24/110-2 User And Installation Manual Download Page 12 | Manualshive

Page: 12 / 32

Mastervolt CHARGEMASTER PLUS 24/110-2 User And Installation Manual Download Page 12

12

ChargeMaster Plus 24/80-2, 24/110-2

–

User and Installation Manual

CAUTION!

Too-thin cables and/or loose
connections

can

cause

dangerous overheating of the
cables

and/or

terminals.

Therefore, tighten all connections
well, to limit transition resistance
as far as possible. Use cables of
the correct size.

CAUTION!

Short  circuiting  or  reversing
polarity  may  lead  to  serious
damage  to  the  batteries,  the
ChargeMaster  Plus,  the  cabling
and/or  the  terminal  connections.
Fuses between the batteries and
the  ChargeMaster  Plus  cannot
prevent  damage  caused  by
reversed polarity. The damage as
a  result  of  reverse  polarity  is
detectable

by

the

service

department and is not covered by
the warranty.

3.8

Installation step-by-step

1

2

3

Fix the enclosure to the wall by
fastening two screws at the lower
side of the enclosure as well.

4

Open the connection compartment
by loosening the two screws.

«
...
10
11
12
13
14
...
»

Summary of Contents for CHARGEMASTER PLUS 24/110-2

































Reviews:

No comments