– 4 –
– 5 –
Pull-out side
extension table
supports large format
tiles and slabs
Metal
screw
(B) Grounded
outlet box
(A) Grounding pin
figure 2
EXTENSION CORDS
1 . Use only extension cords that are intended
for outdoor use . These extension cords are
identified by a marking “Acceptable for use
with outdoor appliances: store indoors while
not in use .” Use only extension cords having
an electrical rating not less than the rating of
the product . Do not use damaged extension
cords . Examine extension cord before using
and replace if damaged . Do not abuse
extension cords and do not yank on any cord
to disconnect . Keep cord away from heat and
sharp edges . Always disconnect the extension
cord from the receptacle before disconnecting
the product from the extension cord .
TO REDUCE THE RISk
OF ELECTROCUTION, kEEP ALL CONNECTIONS
DRY AND OFF THE GROUND. DO NOT TOUCH
PLUG WITH WET HANDS.
2 . Ground Fault circuit Interrupter (GFCI)
protection should be provided on the
circuit(s) or outlet(s) to be used for the tile
saw . Receptacles are available having built-in
GFCI protection and may be used for this
measure of safety .
3 .
use proper eXtension cord.
Make sure
your extension cord is in good condition .
When using an extension cord, be sure to use
a cord heavy enough to carry the current your
product will draw . An undersized cord will
cause a drop in line voltage, resulting in loss
power and overheating . TABLE 1 shows the
correct size to use depending on cord length
and nameplate ampere rating . If in doubt, use
the next heavier gauge . The smaller the
gauge number, the heavier the cord .
note
: When using an extension cord, ensure
all cords are no smaller than #12 gauge, rated
at a 20-amp minimum, and equipped with
3-prong plugs . Use of anything smaller may
result in overheating or burn out of the motor . It
is recommended to have an electrician check
the voltage at the saw motor to ensure proper
voltage to run the saw efficiently and safely .
CALIFORNIA
PROPOSITION 65
SOME DUST CREATED
BY POWER SANDING, SAWING, GRINDING,
DRILLING AND OTHER CONSTRUCTION
ACTIvITIES CONTAIN CHEMICALS kNOWN TO
THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIvE
HARM.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other
masonry products
• Arsenic and chromium from chemically-
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work . To reduce your exposure to these
chemicals: work in well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specifically designed
to filter out microscopic particles .
DESCRIPTION
Before attempting to use any tool, be sure
to familiarize yourself with all the operating
features and safety instructions .
Ampere rating
Volts
Total length of cord in feet
120 V
25 ft .
50 ft .
100 ft .
150 ft .
More than No more than
AWG
0
6
18
16
16
14
6
10
16
14
16
12
table 1
KnOW yOUr SaW
Your tile saw has many built-in features (see
FIGURE 3) for fast, efficient cutting of ceramic,
porcelain, marble, slate or limestone wall or floor
tile . The durable 8 inch blade cuts tile up to 1-1/2 in .
thick . The built-in handle allows easy transporting .
PrOdUCt SPeCiFiCatiOnS
Input:
11.3 amps
No-load Speed:
3420 rpm
Output:
1-1/3 hp motor
Blade Diameter:
8 in. (203 mm)
Arbor:
5/8 in.
Rating:
120 volts~60 hz ac
Depth of Cut:
1 3/8 in. (35 mm)
Cutting Capacity:
30" at 90°, 21" at 45°
ASSEMBLY
FOLLOW ALL OF THE
ASSEMBLY AND OPERATION INSTRUCTIONS
COMPLETELY BEFORE CONNECTING THE SAW
TO A POWER SOURCE OR TURNING THE MOTOR
ON.
UnPaCKinG
1 . Remove all packing materials from around your
saw .
2 . Carefully lift the saw from carton and place
it on a level work surface .
3 . Do not discard the packing materials until
you have carefully inspected the saw for
loose or damaged parts .
The following items are included in box with
your tile saw:
• Folding stand
• Universal Angle Guide
• 8 in. premium continuous rim diamond blade
• 2 wrenches
• Hex key
• Water pump
• Water tray
• Extension table
4 . Inspect the saw carefully to make sure
that no breakage or damage has occurred
during shipping . If any parts are damaged
or missing, return the saw to your place of
purchase .
IF ANY PARTS ARE
DAMAGED OR MISSING, DO NOT ATTEMPT
TO OPERATE THIS SAW. OPERATING THIS
SAW WITH DAMAGED OR MISSING PARTS
COULD RESULT IN POSSIBLE SERIOUS
PERSONAL INJURY.
Flexible cord rod keeps
encapsulated power
cords safely away from
the cutting table
Adjustable pivoting rail
for quick and easy 45°
and 90° miter cuts and
bevel cuts
Plunge cutting head for
making interior cuts
1-1/2HP, 10A inductor motor
is powerful and long lasting
Steel blade guard
accommodates both 8” and
7” blades (8” continuous rim
diamond blade included)
Adjustable
pull-out handle
Large locking wheels for
easy jobsite transport
Durable folding stand
for convenient storage
and transportation
Rubber matting
provides a slip resistant
working surface
figure 3
Innovative water transport
system makes water fill-ups
and drainage clean, fast and
efficient (requires standard
garden hose, sold separately)
Universal quick-adjust angle
guide and rip fence for quick
and accurate miter cuts from
0° to 45°
