MasterCraft MIG 140 Instruction Manual Download Page 17 | Manualshive

Page: 17 / 54

background image

IMPOR

TANT INFORMA

TION

13

MIG 140 INVERTER WELDER 058-9305-6

Inert gas connection

This connection is located in the back panel and connects the inert gas hose from the gas cylinder
to the welder providing the welder with shielding gas in the MIG welding mode.

MIG gun connection

This connection is located in the lower front panel and serves as a connection for both the wire feed
and shielding gas for the MIG gun or spool gun during the MIG welding mode.

MIG gun trigger connection

This MIG gun trigger connection (1) is located
in the lower front panel and connects the
4

-

pin quick connect plug of the MIG gun or the

spool gun (not included) with the welder.
Connections 1 and 2 are provided for the MIG
gun/spool gun and connections 3 and 4 are
provided for the wire feed motor.

MIG/stick selector

This selector is located on the upper front panel and used to select either MIG welding mode or stick
welding mode.

Power switch

This switch is located on the back panel to turn the welder ON or OFF. In the OFF position, there is
no power supply to the MIG gun or electrode holder circuit of the welder. In the ON position, power
is supplied to the main transformer and control circuit. Always turn the power switch OFF and unplug
the welder before performing any maintenance.

Power ON indicator

This indicator is located on the upper front panel and glows when the welder is turned ON.

Spool gun/MIG selector

This selector is located on the upper front panel. It is switched to spool gun mode when a spool gun
(not included) is being used, otherwise it should be in the MIG mode.

Thermal overload indicator

This indicator is located on the upper front panel. It glows when the welder is overloaded and the
internal temperature is too high. The welder will turn off automatically during overload condition. The
fan continues to work even if the welder shuts down. When the internal temperature is decreased,
this indicator stops glowing indicating that the welder is ready to use.

1

2

3

4

MC-589305-02

1

IGBT INVER

TER WIRE FEED WELDER

SOUDEUSE DEVIDOIR INVERSEUR IGBT

«
...
15
16
17
18
19
...
»

Summary of Contents for MIG 140























































Reviews:

No comments

Related manuals for MIG 140

Brand: Campbell Hausfeld Pages: 12

Brand: Campbell Hausfeld Pages: 44

Brand: HALDER Pages: 2

Brand: Jasic Pages: 30

Brand: Najm Alfarqadain Pages: 2

Brand: Unisto Pages: 2

TIG200PACDC PFC

Brand: Jasic Pages: 52

Smartvest FUSG35000A

Brand: Abus Pages: 4

RIS 400PE/PW EKO 3.0

Brand: Salda Pages: 68

Brand: Gabarron Pages: 16

HOME THEATER SPEAKERS

Brand: Sonance Pages: 8

Brand: Cal-Royal Pages: 2

Brand: U-Line Pages: 5

Blazer Express 16

Brand: HIKVISION Pages: 27

Brand: TradeWeld Pages: 11

Brand: ROEL Pages: 28

EASY CLEAR EQ-12-TH

Brand: Bunn Pages: 2

MR Confon Starter f MKII+

Brand: Cambridge Research Systems Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands