background image

16

17

model no. 299-1978-8  |  contact us 1-800-689-9928

OPER

ATING INSTRUCTIONS

OPER

ATING INSTRUCTIONS

 

 

 

 

 

WARNING!

Risk of bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s 
maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed 
the maximum pressure rating. 

 

 

If the pump has been transported or turned upside down (even partially), allow the pump to sit in a normal, 
upright position for approximately 10 minutes before starting.    

 

High temperatures are generated by the electric motor and the pump. To prevent burns or other injuries, 
DO NOT touch the air compressor while it is running. Allow it to cool before handling or servicing. Keep 
children away from the air compressor at all times.   

WARNING!

WARNING!

 

 

 

 

 

CAUTION!

Escaping air and moisture can propel debris that may cause eye injury. Wear safety goggles when opening the 
drain valve. 

WARNING!

To avoid personal injury: always shut off and unplug the unit, and relieve all air pressure from the system before 
performing any service on the air compressor.

Risk of unsafe operation. Unit cycles automatically when power is on. When performing maintenance you may be 
exposed to voltage sources or compressed air. Disconnect power source from the compressor and bleed off all 
air pressure. 

WARNING!

Before each start-up

1.

Set the pressure switch (C) to the OFF position. 

2.

Turn the air pressure regulator knob (E) counterclockwise until it stops.

3.

Attach hose and accessories.

How to start

1.

Close the tank drain valve (I).

2.

Plug in the power cord (K).

3.

Set the pressure switch (C) to the ON position and allow tank pressure to build. Motor will 

stop when tank pressure reaches “cut-out ” pressure.

4.

Turn the air pressure regulator (E) counterclockwise until it stops.

5.

The compressor is ready for use.

How to shut down

1. Set the pressure switch (C) to the OFF position. 
2. Unplug the power cord (K).
3. Reduce the pressure in the tank through the outlet hose. Pulling the safety valve (D), and keeping it open

,

 

will also reduce the pressure in the tank.   

Summary of Contents for 299-1978-8














Reviews: